2000 Toyota Yaris

Nearside Front Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Front Tyre worn close to legal limit/worn on edge low edges of tread (5.2.3 (e))

Nearside Headlamp lens slightly defective (4.1.1 (b) (i))

Nearside Rear Service brake binding but not excessively (1.2.1 (f))

Nearside Suspension component mounting repair covered in underseal outer sill to sill backing area weld repair (5.3.6 (a) (i))

Offside Front Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Suspension component mounting prescribed area is corroded but not considered excessive under body [subframe mount area] (5.3.6 (a) (i))

Offside Front Tyre worn close to legal limit/worn on edge bald inner edge of tread (5.2.3 (e))

Offside Headlamp lens slightly defective (4.1.1 (b) (i))

Rear Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. (1.2.1 (b) (i))

Rear Service brake fluctuating, but not excessively (1.2.1 (e))

Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))

Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b))

Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b))

Front Exhaust system insecure not supported [mounts broken] (6.1.2 (a))

Nearside Rear Passenger's seat backrest cannot be secured in the upright position. (6.2.6 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch area (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch area (5.3.6 (a) (i))

Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill area (7.1.1 (a) (i))

Offside Front Suspension component missing lower ball joint split pin (5.3.3 (a) (ii)) DANGEROUS

Nearside Front Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Front Tyre worn close to legal limit/worn on edge low edges of tread (5.2.3 (e))

Nearside Headlamp lens slightly defective (4.1.1 (b) (i))

Nearside Rear Service brake binding but not excessively (1.2.1 (f))

Nearside Suspension component mounting repair covered in underseal outer sill to sill backing area weld repair (5.3.6 (a) (i))

Offside Front Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Suspension component mounting prescribed area is corroded but not considered excessive under body [subframe mount area] (5.3.6 (a) (i))

Offside Front Tyre worn close to legal limit/worn on edge bald inner edge of tread (5.2.3 (e))

Offside Headlamp lens slightly defective (4.1.1 (b) (i))

Rear Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. (1.2.1 (b) (i))

Rear Service brake fluctuating, but not excessively (1.2.1 (e))

All weld repairs heavily undersealed making hard to inspect

Brake pipe slightly corroded (3.6.B.2c)

Front Brake pad(s) wearing thin (3.5.1g)

Nearside Front Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Front Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

coil spring corroded (2.4.C.1b)

underbody corrosion

Exhaust emissions Lambda reading after 2nd fast idle outside specified limits (7.3.D.3)

Exhaust emissions carbon monoxide content after 2nd fast idle excessive (7.3.D.3)

Exhaust emissions carbon monoxide content at idle excessive (7.3.D.4)

Exhaust emissions hydrocarbon content after 2nd fast idle excessive (7.3.D.3)

Nearside Rear Suspension component mounting prescribed area is inadequately repaired baking sill not fully welded on seam (2.4.A.3)

Offside Rear Suspension component mounting prescribed area is excessively corroded backing sill (2.4.A.3)

Brake pipe slightly corroded (3.6.B.2c)

Front Brake pad(s) wearing thin (3.5.1g)

Nearside Front Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Front Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

coil spring corroded (2.4.C.1b)

underbody corrosion

Front Sub-frame corroded but not seriously weakened (2.4.G.1)

Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Nearside Front Anti-roll bar linkage rubber mounting deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Front Suspension arm corroded but not seriously weakened wishbone (2.4.G.1)

Nearside Headlamp has a product on the lens but not seriously reducing light output (1.7.5a)

Nearside Rear Direction indicator slightly discoloured (1.4.A.2f)

Offside Front Anti-roll bar linkage rubber mounting deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Front Suspension arm corroded but not seriously weakened wishbone (2.4.G.1)

Offside Headlamp has a product on the lens but not seriously reducing light output (1.7.5a)

underbody corrosion

Exhaust emissions Lambda reading after 2nd fast idle outside specified limits (7.3.D.3)

Exhaust emissions carbon monoxide content after 2nd fast idle excessive (7.3.D.3)

Exhaust emissions carbon monoxide content at idle excessive (7.3.D.4)

Exhaust emissions hydrocarbon content after 2nd fast idle excessive (7.3.D.3)

Nearside front brake binding (3.7.B.1)

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Registration plate lamp not working (1.1.C.1d)

Offside front brake binding (3.7.B.1)

Windscreen washer provides insufficient washer liquid (8.2.3)

Front Sub-frame corroded but not seriously weakened (2.4.G.1)

Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Nearside Front Anti-roll bar linkage rubber mounting deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Front Suspension arm corroded but not seriously weakened wishbone (2.4.G.1)

Nearside Headlamp has a product on the lens but not seriously reducing light output (1.7.5a)

Nearside Rear Direction indicator slightly discoloured (1.4.A.2f)

Offside Front Anti-roll bar linkage rubber mounting deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Front Suspension arm corroded but not seriously weakened wishbone (2.4.G.1)

Offside Headlamp has a product on the lens but not seriously reducing light output (1.7.5a)

underbody corrosion

Front Sub-frame corroded but not seriously weakened (2.4.G.1)

Nearside Front Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Headlamp has a product on the lens but not seriously reducing light output (1.7.5a)

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive backing sill (2.4.A.3)

Offside Front Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Headlamp has a product on the lens but not seriously reducing light output (1.7.5a)

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive backing sill (2.4.A.3)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

brake pipes covered in grease

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Nearside Outer Suspension component mounting prescribed area is excessively corroded sill (2.4.A.3)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Outer Suspension component mounting prescribed area is excessively corroded sill (2.4.A.3)

rear brake application uneven (3.7.B.2)

Front Sub-frame corroded but not seriously weakened (2.4.G.1)

Nearside Front Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Headlamp has a product on the lens but not seriously reducing light output (1.7.5a)

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive backing sill (2.4.A.3)

Offside Front Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Headlamp has a product on the lens but not seriously reducing light output (1.7.5a)

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive backing sill (2.4.A.3)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

brake pipes covered in grease

Nearside Headlamp has a product on the lens but not seriously reducing light output (1.7.5a)

Offside Headlamp has a product on the lens but not seriously reducing light output (1.7.5a)

Parking brake lever has little reserve travel (3.1.6b)

both front tyres worn on edge !!!!!!!

o/s/f tyre worn close to wear limit

Exhaust emissions carbon monoxide content after 2nd fast idle excessive (7.3.D.3)

Exhaust emissions carbon monoxide content at idle excessive (7.3.D.4)

Nearside Inner Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Inner Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Outer Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Inner Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Lower Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2)

Nearside Headlamp has a product on the lens but not seriously reducing light output (1.7.5a)

Offside Headlamp has a product on the lens but not seriously reducing light output (1.7.5a)

Parking brake lever has little reserve travel (3.1.6b)

Parking brake: parking brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.7)

Rear Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.5b)

both front tyres worn on edge !!!!!!!

o/s/f tyre worn close to wear limit

Front Brake pad(s) wearing thin (3.5.1g)

Front Sub-frame corroded but not seriously weakened (2.4.G.1)

Nearside Front Macpherson strut corroded but not seriously weakened (2.4.G.1)

Nearside Inner Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Front Macpherson strut corroded but not seriously weakened (2.4.G.1)

Parking brake lever has little reserve travel (3.1.6b)

Rear Sub-frame corroded but not seriously weakened (2.4.G.1)

n/s/f tyre worn on edge

o/s/f tyre worn on edge

slight under body corrosion

Nearside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Nearside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Rear Direction indicators incorrect colour (1.4.A.2f)

Offside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Exhaust emissions carbon monoxide content at idle excessive (7.3.D.4)

Nearside Front position lamp(s) not working (1.1.A.3b)

Nearside Rear Passenger's seat cannot be secured in the upright position. (6.2.A.2)

Nearside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Rear Brake pipe excessively corroded (3.6.B.2c)

Offside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

n/s and o/s/f drive shafed inner c.v boots are split

Exhaust emissions Lambda reading after 2nd fast idle outside specified limits (7.3.D.3)

Nearside Front Headlamp aim not tested (1.8.A.1c)

Nearside Front Headlamp not working on dipped beam (1.7.5a)

Nearside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Rear Exhaust has a major leak of exhaust gases (7.1.2)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

n/s and o/s/f drive shafed inner c.v boots are split

n/s/f wash jet missing screen

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Rear coil spring incomplete (2.4.C.1a)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

need's trcking !!

Nearside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Exhaust system not adequately supported (7.1.1)

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Suspension arm rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Offside Rear Coil spring not correctly located (2.4.C.2)

Parking brake lever has no reserve travel (3.1.6b)

Nearside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Front Lower Bonded suspension unit deteriorated but can function as intended (2.4.F.3)

Offside Front Windscreen wiper blade deteriorated (8.2.2)

corrosion to exhaust

corrosion to front crossmember

corrosion to sump

nearside front inner driveshaft boot split

nearside front tyre worn

travel on handbrake