2003 Fiat Seicento

Front Upper Macpherson strut pin or bush worn but not resulting in excessive movement o/s/n/s (5.3.4 (a) (i))

Nearside Front Coil spring corroded (5.3.1 (b) (i))

Offside Front Outer Drive shaft joint constant velocity boot severely deteriorated (6.1.7 (g) (i))

Offside Rear Shock absorbers has a reduced damping effect (5.3.2 (d))

Oil leak, but not excessive (8.4.1 (a) (i))

Rear Coil spring corroded o/s/n/s (5.3.1 (b) (i))

Rear Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Rear Position lamp slightly affected by the operation of another lamp (4.2.3 (c))

Underbody covered with underseal

Oil leak, but not excessive (8.4.1 (a) (i))

Brake pipe corroded, covered in grease or other material front to rear (1.1.11 (c))

Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Brake pipe corroded, covered in grease or other material Front to rear (1.1.11 (c))

Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Battery insecure and likely to fall from carrier (4.13 (a) (ii))

Offside Front Service brake excessively fluctuating (1.2.1 (e))

Offside Side repeater not working (4.4.1 (a) (ii))

Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i))

Service brake efficiency below requirements (1.2.2 (a) (i))

Brake pipe corroded, covered in grease or other material Front to rear (1.1.11 (c))

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Nearside Front Service brake fluctuating, but not excessively (1.2.1 (e))

Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Exhaust emissions Lambda reading after 2nd fast idle outside specified limits (7.3.D.3)

Front Exhaust has a major leak of exhaust gases (7.1.2)

Front Exhaust has a major leak of exhaust gases at flexi (7.1.2)

Nearside Rear Rear wheel bearing rough when rotated (2.6.1)

Nearside rear parking brake recording little or no effort (3.7.B.6a)

Offside Front Brake pipe excessively corroded (3.6.B.2c)

Offside Front position lamp(s) not working (1.1.A.3b)

Offside Headlamp aim too low (1.8)

Offside Rear Rear wheel bearing rough when rotated (2.6.1)

Offside rear parking brake recording little or no effort (3.7.B.6a)

Parking brake: efficiency below requirements (3.7.B.7)

Offside Front Brake pipe slightly corroded (3.6.B.2c)

Parking brake lever has little reserve travel (3.1.6b)

Offside Rear wheel bearing rough when rotated (2.6.1)

Offside Front Brake pipe slightly corroded (3.6.B.2c)

Parking brake lever has little reserve travel (3.1.6b)

Front Brake pipe slightly corroded (3.6.B.2c)

Front Windscreen wiper does not clear the windscreen effectively (8.2.2)

Rear Brake pipe slightly corroded (3.6.B.2c)

Front Brake pipe slightly corroded (3.6.B.2c)

Rear Brake pipe slightly corroded (3.6.B.2c)

Brake hose has slight corrosion to ferrules (3.6.B.4e)

Parking brake lever has little reserve travel (3.1.6b)

Nearside rear brake recording little or no effort (3.7.B.5a)

Nearside rear parking brake recording little or no effort (3.7.B.6a)

Offside rear brake recording little or no effort (3.7.B.5a)

Offside rear parking brake recording little or no effort (3.7.B.6a)

Parking brake: efficiency below requirements (3.7.B.7)

Nail in offside rear tyre

Offside Rear Shock absorber has a light misting of oil (2.7.3)

CAT HEAT SHIELD RATTLING.

O/S/F BRAKES BINDING SLIGHTLY.

O/S/R TYRE;SCREW IN TREAD.

Nearside Headlamp aim too high (1.8)

Offside Headlamp aim too high (1.8)

Offside Rear rear brake binding (3.7.B.1)

CAT HEAT SHIELD RATTLING.

O/S/F BRAKES BINDING SLIGHTLY.

O/S/R TYRE;SCREW IN TREAD.

UNABLE TO CHECK O/S/R WHEEL BEARINGS.

Front Exhaust has a major leak of exhaust gases (7.1.2)

Front Exhaust has part of the system excessively deteriorated (7.1.1a)

Offside rear brake binding (3.7.B.1)

Parking brake: efficiency below requirements (3.7.B.7)

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1) DANGEROUS

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1) DANGEROUS