2007 Ford Connect

Brake pipe corroded, covered in grease or other material Near and Offside front to rear corroded (1.1.11 (c))

Coolant leak radiator leaking ()

Nearside Front Tyre worn close to legal limit/worn on edge worn HEAVILY on the inner shoulder (5.2.3 (e))

Offside Rear Shock absorbers has a reduced damping effect (5.3.2 (d))

Rear Exhaust has a minor leak of exhaust gases exhaust box (6.1.2 (a))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Front Anti-roll bar ball joint excessively worn (5.3.4 (a) (i))

Stop lamp(s) not working Nearside & offside (4.3.1 (a) (ii))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Nearside Rear Shock absorbers has light misting of oil (5.3.2 (b))

Nearside Rear Tyre slightly damaged (5.2.3 (d) (ii))

Nearside Windscreen damaged but not adversely affecting driver's view (3.2 (a) (i))

Offside Front Inner Drive shaft joint constant velocity boot severely deteriorated (6.1.7 (g) (i))

Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Sill area (7.1.1 (a) (i))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill area (5.3.6 (a) (i))

Nearside Front Tyre has a tear, caused by separation or partial failure of its structure (5.2.3 (d) (ii)) DANGEROUS

Nearside Rear Shock absorbers has light misting of oil (5.3.2 (b))

Nearside Rear Tyre slightly damaged (5.2.3 (d) (ii))

Nearside Windscreen damaged but not adversely affecting driver's view (3.2 (a) (i))

Offside Front Inner Drive shaft joint constant velocity boot severely deteriorated (6.1.7 (g) (i))

Nearside Windscreen damaged but not adversely affecting driver's view (3.2 (a) (i))

Front Exhaust has a major leak of exhaust gases (6.1.2 (a))

Nearside Rear Tyre has a cut in excess of the requirements deep enough to reach the ply or cords (5.2.3 (d) (i))

Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Rear Exhaust has a major leak of exhaust gases (6.1.2 (a))

Nearside Front Brake pad(s) less than 1.5 mm thick (1.1.13 (a) (ii)) DANGEROUS

Nearside Windscreen damaged but not adversely affecting driver's view (3.2 (a) (i))

Offside Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Stop lamp(s) all not working (4.3.1 (a) (iii))

Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Nearside Front Anti-roll bar linkage ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Nearside Rear Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Offside Front Anti-roll bar linkage ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Offside Rear Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Oil leak, but not excessive Sump (8.4.1 (a) (i))

Engine MIL inoperative or indicates a malfunction (8.2.2.2 (g))

Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Nearside Front Anti-roll bar linkage ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Nearside Rear Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Offside Front Anti-roll bar linkage ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Offside Rear Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Oil leak, but not excessive Sump (8.4.1 (a) (i))

Nearside Front Inner Front constant velocity joint gaiter damaged, but preventing the ingress of dirt (2.5.C.1a)

Nearside Front Inner Front constant velocity joint gaiter damaged, but preventing the ingress of dirt (2.5.C.1a)

Nearside Registration plate lamp not working (1.1.C.1d)

Offside Stop lamp not working (1.2.1b)

nsf tyre on limit

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)