2006 Suzuki GZ125

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Front Brake lever is bent but brake can still be readily applied (1.1.2 (d))

Front Motorcycle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Front Shock absorber has a serious fluid leak (5.3.2 (b))

Nearside Front Motorcycle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i))

Rear Stop lamp not working (4.3.1 (a) (ii))

Exhaust silencer likely to become detached (8.1.1 (b) (ii)) DANGEROUS

Front Brake pad(s) less than 1.0 mm thick (1.1.13 (a)) DANGEROUS

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Front Brake lever is bent but brake can still be readily applied (1.1.2 (d))

Front Motorcycle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Exhaust is leaking but is not excessively noisey (7.1.1b)

Front Brake disc(s) slightly worn (3.2.A1l)

Motorcycle structure slightly corroded the footrest area of the frame is quite rusted and will require attention prior to the next MoT test (6.1.1a)

Rear Tyre worn close to the legal limit (4.1.3(ii))

Front Brake disc(s) slightly worn (3.2.A1l)

Front Brake lever is bent but brake can still be readily applied (3.1.3c)

Front Brake pad(s) close to minimum limit (3.2.A1f(i))

Front suspension has slight corrosion (2.3.8)

Drive chain excessively tight (6.2.1d)

Rear Drive chain sprocket worn to excess (6.2.1e)

Front Brake disc(s) slightly worn (3.2.A1l)

Front Brake fluid reservoir fluid level low (3.2.B1d)

Front Brake lever is bent but brake can still be readily applied (3.1.3c)

Front Brake pad(s) close to minimum limit (3.2.A1f(i))

Front suspension has slight corrosion (2.3.8)

Front Brake disc(s) slightly worn (3.2.A1l)

Front Brake lever is bent but brake can still be readily applied (3.1.3c)

Drive chain excessively loose (6.2.1d)

Front Stop lamp does not illuminate immediately a brake applies (1.3.1a)

Handlebar deformed (2.1.1b)

Nearside Front shock absorber seal failed and leaking oil (2.3.3)

Rear Floor brake test indicates a sticking brake (3.3.C2c)

Front Brake disc(s) slightly worn (3.2.A1l)

Front Brake lever is bent but brake can still be readily applied (3.1.3c)

Front Brake pad(s) close to minimum limit (3.2.A1f(i))

Front suspension has slight corrosion (2.3.8)

Drive chain slightly loose (6.2.1d)

Front Brake disc(s) slightly worn (3.2.A1l)

handlebars very slightly bent

Drive chain slightly loose (6.2.1d)

Front Brake disc(s) slightly worn (3.2.A1l)

Nearside Front Brake caliper(s) securing bolt(s) missing (3.2.A1j)

handlebars very slightly bent

Front wheel bearings are slightly rough (2.3.5b)

Steering movement slightly 'notchy' (2.2.1a)

Front Brake pad(s) less than 1.5 mm thick (3.2.A1f(i))

Front wheel bearings are slightly rough (2.3.5b)

Steering movement slightly 'notchy' (2.2.1a)

Clutch lever shortened. (6.2.1g)

Front Brake disc(s) slightly worn (3.2.A1l)

Steering movement slightly 'notchy' (2.2.1b)

Front Brake pad(s) less than 1.5 mm thick (3.2.A1f(i))

Front Tyre tread depth is below minimum requirements of 1.0mm (4.1.3(ii))

Front position lamp does not illuminate immediately when switched on (1.1.3a)

Rear Wheel spoke missing (4.2.1b)

Clutch lever shortened. (6.2.1g)

Front Brake disc(s) slightly worn (3.2.A1l)

Steering movement slightly 'notchy' (2.2.1b)

Front Brake pad(s) less than 1.5 mm thick (3.2.A1f(i))

Rear Stop lamp does not illuminate immediately a brake applies (1.3.1a)

Rear Tyre tread depth is below minimum requirements of 1.0mm (4.1.3(ii))