MOT Status
ValidMileage
95,775 miSignificantly above average — investigate
Not all car check providers offer a guarantee. Don't risk buying from services that can't back their data. CarVerify reports include a £30,000 finance data guarantee.
Vehicle Details
All premium checks include
50+ data pointsMOT History
Nearside Body mounting fixings insecure Centre chassis (6.2.2 (c) (i))
Nearside Front Steering system excessively rough (2.1.1 (a))
Nearside Rear Body mounting fixings insecure chassis (6.2.2 (c) (i))
Offside Rear Body mounting fixings insecure Center chassis (6.2.2 (c) (i))
Offside Rear Body mounting fixings insecure cvhassis (6.2.2 (c) (i))
Offside Rear Upper Coil spring mounting corroded and seriously weakened (5.3.1 (b) (i))
Nearside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced Inner sill underside (7.1.1 (a) (i))
Offside Front Lower Axle swivel pins and bushes swivel pin and/or bush excessively worn (5.1.2 (b) (i))
Rear Brake pipe excessively corroded Front to rear (1.1.11 (c))
Offside Front Brake hose slightly twisted (1.1.12 (b) (i))
Exhaust mounting defective (6.1.2 (a))
Front Brake pipe corroded, covered in grease or other material to rear at rear (1.1.11 (c))
Towbar obstructing the registration plate (6.1.6 (f) (i))
Brake hose has slight corrosion to ferrule all flexi hoses (1.1.12 (f) (i))
Brake pipe corroded, covered in grease or other material all steel pipes (1.1.11 (c))
Coil spring corroded all springs (5.3.1 (b) (i))
Fuel Pipe/s corroded ()
Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))
Nearside Headlamp has a product on the lens but not seriously reducing light output (4.1.4 (b))
Offside Headlamp has a product on the lens but not seriously reducing light output (4.1.4 (b))
Rear Suspension arm pin or bush worn but not resulting in excessive movement both trailing arms (5.3.4 (a) (i))
chip to windscreen
initial signs of general underbody surface corrosion showing
outer sill covers fitted to vehicle
Nearside Front Lower Axle swivel pins and bushes swivel pin and/or bush excessively worn Grease weeping from the seal (5.1.2 (b) (i))
Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Underside corroded & holed (7.1.1 (a) (i))
Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i))
Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i))
Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))
Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))
Brake pipe corroded, covered in grease or other material Front to rear (1.1.11 (c))
Coil spring corroded Front & rear (5.3.1 (b) (i))
Fuel Pipe/s corroded ()
Headlamp has a product on the lens but not seriously reducing light output (4.1.4 (b))
Nearside Headlamp aim too low (4.1.2 (a))
Offside Rear Inner Seat belt anchorage prescribed area is corroded but not considered excessive Sill underside (7.1.1 (a) (i))
Plastic outer sill covers fitted
Rear Suspension arm pin or bush worn but not resulting in excessive movement Trailing arms (5.3.4 (a) (i))
Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))
Vehicle structure slightly corroded within 30cm of towbar mounting (6.1.6 (i) (i))
Windscreen damaged but not adversely affecting driver's view Stone chips (3.2 (a) (i))
front and rear propshaft UJ's slight play
Brake pipe corroded, covered in grease or other material all vehicle pipes (1.1.11 (c))
Front Coil spring corroded (5.3.1 (b) (i))
Fuel Pipe/s corroded ()
Nearside Headlamp has a product on the lens but not seriously reducing light output (4.1.4 (b))
Nearside Rear Inner Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))
Nearside Rear Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Offside Headlamp has a product on the lens but not seriously reducing light output (4.1.4 (b))
Offside Rear Inner Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))
Offside Rear Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Rear Coil spring corroded (5.3.1 (b) (i))
Vehicle structure slightly corroded within 30cm of towbar mounting (6.1.6 (i) (i))
chip to windscreen
front and rear propshaft uj;s slight play
rear exhaust vibrating on chassis
Anti-lock braking system warning lamp indicates an ABS fault (1.6 (b))
Nearside Stop lamp(s) not working (4.3.1 (a) (ii))
Nearside Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))
Offside Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))
Nearside Rear Tyre has a bulge, caused by separation or partial failure of its structure (5.2.3 (d) (ii)) DANGEROUS
Brake pipe corroded, covered in grease or other material all vehicle pipes (1.1.11 (c))
Front Coil spring corroded (5.3.1 (b) (i))
Fuel Pipe/s corroded ()
Nearside Headlamp has a product on the lens but not seriously reducing light output (4.1.4 (b))
Nearside Rear Inner Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))
Nearside Rear Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Offside Headlamp has a product on the lens but not seriously reducing light output (4.1.4 (b))
Offside Rear Inner Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))
Offside Rear Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Offside Rear Tyre worn close to legal limit/worn on edge 205/70/15 (5.2.3 (e))
Rear Coil spring corroded (5.3.1 (b) (i))
Vehicle structure slightly corroded within 30cm of towbar mounting (6.1.6 (i) (i))
chip to windscreen
front and rear propshaft uj;s slight play
rear exhaust vibrating on chassis
Front Coil spring corroded (5.3.1 (b) (i))
Headlamp has a product on the lens but not seriously reducing light output (4.1.4 (b))
Nearside Front Position lamp light intensity obviously reduced (4.2.3 (a) (i))
Nearside Windscreen wiper blade defective (3.4 (b) (i))
Offside Rear Service brake binding but not excessively (1.2.1 (f))
Offside Windscreen wiper blade defective (3.4 (b) (i))
Oil leak, but not excessive Engine (8.4.1 (a) (i))
Prop shaft joint worn, but not excessively Rear propshaft rear UJ (6.1.7 (c) (i))
Rear Coil spring corroded (5.3.1 (b) (i))
Rear Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Rear shock absorber dust covers corroding
Suspension component mounting prescribed area is corroded but not considered excessive Rear spring top mounts (5.3.6 (a) (i))
Offside Front Service brake excessively binding (1.2.1 (f))
Front Coil spring corroded (5.3.1 (b) (i))
Headlamp has a product on the lens but not seriously reducing light output (4.1.4 (b))
Nearside Front Position lamp light intensity obviously reduced (4.2.3 (a) (i))
Nearside Windscreen wiper blade defective (3.4 (b) (i))
Offside Front Position lamp not working (4.2.1 (a) (ii))
Offside Rear Service brake binding but not excessively (1.2.1 (f))
Offside Windscreen wiper blade defective (3.4 (b) (i))
Oil leak, but not excessive Engine (8.4.1 (a) (i))
Prop shaft joint worn, but not excessively Rear propshaft rear UJ (6.1.7 (c) (i))
Rear Coil spring corroded (5.3.1 (b) (i))
Rear Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Rear shock absorber dust covers corroding
Suspension component mounting prescribed area is corroded but not considered excessive Rear spring top mounts (5.3.6 (a) (i))
Nearside Headlamp has a product on the lens but not seriously reducing light output (4.1.4 (b))
Nearside Rear Suspension arm pin or bush worn but not resulting in excessive movement Rear hockey arm bushes. (5.3.4 (a) (i))
Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive Spring top mount. (5.3.6 (a) (i))
Offside Headlamp has a product on the lens but not seriously reducing light output (4.1.4 (b))
Offside Rear Suspension arm pin or bush worn but not resulting in excessive movement Rear hockey arm bushes. (5.3.4 (a) (i))
Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive Spring top mount. (5.3.6 (a) (i))
Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))
Exhaust has a major leak of exhaust gases Centre section flange to back box. (6.1.2 (a))
Front Registration plate inscription illegible (0.1 (b))
Front Brake pad(s) wearing thin (1.1.13 (a) (ii))
Nearside Headlamp has a product on the lens but not seriously reducing light output (4.1.4 (b))
Nearside Rear Suspension arm pin or bush worn but not resulting in excessive movement Rear hockey arm bushes. (5.3.4 (a) (i))
Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive Spring top mount. (5.3.6 (a) (i))
Nearside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))
Offside Headlamp has a product on the lens but not seriously reducing light output (4.1.4 (b))
Offside Rear Suspension arm pin or bush worn but not resulting in excessive movement Rear hockey arm bushes. (5.3.4 (a) (i))
Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive Spring top mount. (5.3.6 (a) (i))
All rear suspension bushes showing signs of age and wear
Brake pipe slightly corroded (3.6.B.2c)
Exhaust corroding
Front coil spring corroded (2.4.C.1b)
Front hub swivel ball seals leaking oil/grease
Front side lights slightly dim
Headlamp has a product on the light source but not seriously reducing light output Headlight lens deteriorated (1.7.5a)
Plastic outer sill covers fitted
Rear Shock absorber has slight corrosion to the casing (2.7.2a)
Rear brake back plate extension missing!
Rear coil spring corroded (2.4.C.1b)
Slight play in the steering box
Suspension component mounting prescribed area is corroded but not considered excessive Chassis (2.4.A.3)
Suspension spring mounting prescribed area is corroded but not considered excessive Rear Upper Suspension spring mounting (2.4.A.3)
brake disc worn, pitted or scored, but not seriously weakened Front brake disc lipped, Disc pads approx. 50% worn (3.5.1i)
All rear suspension bushes showing signs of age and wear
Brake pipe slightly corroded (3.6.B.2c)
Exhaust corroding
Front Tyre worn close to the legal limit 2mm, Tyres in poor condition, Cracking in the tread and wearing smooth on the outer edges (4.1.E.1)
Front brake disc lipped, Disc pads approx. 50% worn
Front coil spring corroded (2.4.C.1b)
Front hub swivel ball seals leaking oil/grease
Front side lights slightly dim
Headlight aim just above the minimum level
Headlight lens deteriorated
Plastic outer sill covers fitted
Rear Shock absorber has a slightly worn bush (2.7.4)
Rear Shock absorber has slight corrosion to the casing Plus dust covers corroding through (2.7.2a)
Rear Upper Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Rear brake back plate extension corroding. N/S/F badly and O/S/R missing!
Rear coil spring corroded (2.4.C.1b)
Slight play in the steering box
Suspension component mounting prescribed area is corroded but not considered excessive Chassis corroding (2.4.A.3)
All rear suspension bushes showing signs of age and wear
Anti-lock braking system warning lamp indicates an ABS fault (3.4.1c)
Brake pipe slightly corroded (3.6.B.2c)
Exhaust corroding
Front Tyre worn close to the legal limit 2mm, Tyres in poor condition, Cracking in the tread and wearing smooth on the outer edges (4.1.E.1)
Front brake disc lipped, Disc pads approx. 50% worn
Front coil spring corroded (2.4.C.1b)
Front hub swivel ball seals leaking oil/grease
Front side lights slightly dim
Headlight aim just above the minimum level
Headlight lens deteriorated
Plastic outer sill covers fitted
Rear Shock absorber has a slightly worn bush (2.7.4)
Rear Shock absorber has slight corrosion to the casing Plus dust covers corroding through (2.7.2a)
Rear Upper Suspension spring mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Rear brake back plate extension corroding. N/S/F badly and O/S/R missing!
Rear coil spring corroded (2.4.C.1b)
Slight play in the steering box
Suspension component mounting prescribed area is corroded but not considered excessive Chassis corroding (2.4.A.3)
Front brake disc lipped
Front coil spring corroded (2.4.C.1b)
Plastic outer sill covers fitted
Rear brake back plate extension corroding. N/S/F badly and O/S/R missing!
Rear coil spring corroded (2.4.C.1b)
Rear Brakes imbalanced across an axle Axle 2 (3.7.B.5b)
Front brake disc lipped
Front coil spring corroded (2.4.C.1b)
Plastic outer sill covers fitted
Rear brake back plate extension corroding. N/S/F badly and O/S/R missing!
Rear coil spring corroded (2.4.C.1b)
Slight front brake imbalance
Nearside Rear Tyre worn close to the legal limit (4.1.E.1)
Nearside Registration plate lamp not working (1.1.C.1d)
Offside Front position lamp(s) not working (1.1.A.3b)
Offside Rear Tyre worn close to the legal limit (4.1.E.1)
Nearside Rear Tyre worn close to the legal limit (4.1.E.1)
Offside Rear Tyre worn close to the legal limit (4.1.E.1)
Nearside Registration plate lamp not working (1.1.C.1d)
Exhaust has part of the system slightly deteriorated (7.1.1a)
Nearside Rear Tyre has a tear, caused by separation or partial failure of its structure (4.1.D.1b)
Offside Rear Tyre has a tear, caused by separation or partial failure of its structure (4.1.D.1b)
Windscreen has damage to an area in excess of a 10mm circle within zone 'A' (8.3.1a)
Exhaust has part of the system slightly deteriorated (7.1.1a)
Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)
both rear tyres slightly deteriorated
How Reliable is the Suzuki Jimny?
Based on 677,512 MOT tests across 43,507 vehicles.
Top MOT Failure Points
Don't risk it. Know before you buy.
Not all vehicle check providers are the same. Some don't offer a data guarantee, which means if their information is wrong, you're on your own. Every CarVerify report is backed by a £30,000 finance data guarantee.
WJ54 ZBC is a 2004 Suzuki Jimny in Silver with a 1,328cc petrol engine. This vehicle has been through 30 MOT tests with a personal pass rate of 63.3%.
Across all 2004 Suzuki Jimny models, the average MOT pass rate is 75.5% with a typical mileage of 55,220 miles. This particular vehicle has a lower pass rate than the average for its year, which may indicate maintenance issues worth investigating.
The most common reason a Suzuki Jimny fails its MOT is brake pipe excessively corroded, accounting for 18,210 recorded failures. If you're considering buying WJ54 ZBC, it's worth having these areas checked by a mechanic before committing.
The Suzuki Jimny typically stays on UK roads for around 28 years. At 22 years old, this Suzuki Jimny is well into its expected lifespan but still has years ahead.
Frequently Asked Questions
How do I check the history of WJ54 ZBC?
You can check the full history of WJ54 ZBC by running a full vehicle check. This shows you finance, stolen, write-off, MOT history, mileage records and more.
What year was WJ54 ZBC registered?
WJ54 ZBC is a 2004 Suzuki Jimny, first registered on 16 September 2004.
Is WJ54 ZBC safe to buy?
The MOT history for WJ54 ZBC shows 30 tests with a 63.3% pass rate. To check for outstanding finance, stolen markers, write-off history and mileage discrepancies, run a full vehicle check.
Does WJ54 ZBC have outstanding finance?
Finance checks require a premium vehicle report. This checks against all major UK finance providers to see if there is any outstanding finance on WJ54 ZBC. If you buy a car with outstanding finance, the finance company can repossess it.
No warranty or guarantee of accuracy is provided for any free data on this page. The data guarantee applies only to information obtained through the purchase of a full check.