MOT Status
ValidMileage
307,548 miSignificantly above average — investigate
Not all car check providers offer a guarantee. Don't risk buying from services that can't back their data. CarVerify reports include a £30,000 finance data guarantee.
Vehicle Details
All premium checks include
50+ data pointsMOT History
Brake pipe corroded, covered in grease or other material ALL (1.1.11 (c))
Front SUBFRAME CORRODED
Nearside Front Lower Suspension arm ball joint dust cover severely deteriorated (5.3.4 (b) (i))
Nearside Front Lower Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))
Nearside Front Shock absorbers has light misting of oil (5.3.2 (b))
Offside Front Lower Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))
Rear Oil leak, but not excessive (8.4.1 (a) (i))
UNDERBODY COVERED IN PAINT (wet)
Battery insecure but not likely to fall from carrier (4.13 (a) (i))
Brake pipe corroded, covered in grease or other material all (1.1.11 (c))
Front Sub-frame corroded but not seriously weakened and suspension arms (5.3.3 (b) (i))
Nearside Front Shock absorbers has light misting of oil (5.3.2 (b))
underside covered in black paint
underside heavily welded
Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded body mounting (1.1.21 (e) (i))
Battery insecure but not likely to fall from carrier (4.13 (a) (i))
Brake pipe corroded, covered in grease or other material all (1.1.11 (c))
Front Sub-frame corroded but not seriously weakened and suspension arms (5.3.3 (b) (i))
Nearside Front Shock absorbers has light misting of oil (5.3.2 (b))
underside covered in black paint
Central Rear Oil leak, but not excessive diff cover corroded (8.4.1 (a) (i))
Nearside Front Shock absorbers has a reduced damping effect (5.3.2 (d))
Nearside Front Shock absorbers has light misting of oil (5.3.2 (b))
Offside Front Upper Oil leak, but not excessive turbo area (8.4.1 (a) (i))
Offside Rear Exhaust has a minor leak of exhaust gases tail pipe corroded (6.1.2 (a))
the whole body under side is badly corroded all over
Nearside Front Shock absorbers has light misting of oil (5.3.2 (b))
Offside Front Oil leak, but not excessive turbo area (8.4.1 (a) (i))
both front inner wheel arches starting to corrode
engine cover fitted
Nearside inner sill corroeded
Nearside Front Body mounting fixing insecure, but overall security not significantly reduced (6.2.2 (c) (i))
Nearside Rear Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Offside Front Body mounting fixing insecure, but overall security not significantly reduced (6.2.2 (c) (i))
Offside Rear Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Offside inner sill corroded
both front iner wings front body mounts corroded
Horn not working (7.7 (a))
Nearside All outline marker lamps not working (4.2.1 (a) (ii))
Offside All outline marker lamps not working (4.2.1 (a) (ii))
Offside Front Position lamp not working (4.2.1 (a) (ii))
Offside Headlamp not working on dipped beam (4.1.1 (a) (ii))
Offside Rear Position lamp not working (4.2.1 (a) (ii))
Offside Rear fog lamp not working (4.5.1 (a) (ii))
Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))
Nearside Front Body mounting fixing insecure, but overall security not significantly reduced (6.2.2 (c) (i))
Nearside Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Nearside inner sills holed and corroded
Offside Front Body mounting fixing insecure, but overall security not significantly reduced (6.2.2 (c) (i))
Offside Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Offside inner sills holed and corroded
Nearside Front Integral body structure is fractured but structural rigidity is not significantly reduced inner arch (6.1.1 (a) (i))
Nearside Integral body structure is corroded but structural rigidity is not significantly reduced inner sill (6.1.1 (c) (i))
Nearside Rear Integral body structure is corroded but structural rigidity is not significantly reduced inner arch (6.1.1 (c) (i))
Offside Front Integral body structure is corroded but structural rigidity is not significantly reduced inner sill (6.1.1 (c) (i))
Offside Integral body structure is corroded but structural rigidity is not significantly reduced inner sill (6.1.1 (c) (i))
Offside Rear Integral body structure is corroded but structural rigidity is not significantly reduced inner arch (6.1.1 (c) (i))
Offside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i))
Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))
Nearside Front Integral body structure is fractured but structural rigidity is not significantly reduced inner arch (6.1.1 (a) (i))
Nearside Integral body structure is corroded but structural rigidity is not significantly reduced inner sill (6.1.1 (c) (i))
Nearside Rear Integral body structure is corroded but structural rigidity is not significantly reduced inner arch (6.1.1 (c) (i))
Offside Front Integral body structure is corroded but structural rigidity is not significantly reduced inner sill (6.1.1 (c) (i))
Offside Integral body structure is corroded but structural rigidity is not significantly reduced inner sill (6.1.1 (c) (i))
Offside Rear Integral body structure is corroded but structural rigidity is not significantly reduced inner arch (6.1.1 (c) (i))
Anti-lock braking system warning lamp indicates an ABS fault (1.6 (b))
Horn not working (7.7 (a) (ii))
Parking brake efficiency below requirements (1.4.2 (a) (i))
Position lamp not working (4.2.1 (a) (ii))
Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))
Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))
Supplementary restraint system warning lamp indicates a fault (7.1.6 (a))
Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))
Integral body structure is corroded but structural rigidity is not significantly reduced inner sill (6.1.1 (c) (i))
Nearside Front Integral body structure is corroded but structural rigidity is not significantly reduced inner arch (6.1.1 (c) (i))
Offside Front Integral body structure is corroded but structural rigidity is not significantly reduced inner wheel arch (6.1.1 (c) (i))
Offside Integral body structure is corroded but structural rigidity is not significantly reduced inner sills (6.1.1 (c) (i))
Both chassis corroded
Nearside Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))
Nearside Front Lower Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))
Nearside Rear Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))
Nearside rear inner lower panel corroded and holed
Offside Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))
Offside Front Lower Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))
Offside Rear Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))
Offside rear out rigger corroded and holed
All outline marker lamps not working (4.2.1 (a) (ii))
Brake load sensing valve seized but ABS functioning (1.1.17 (c) (i))
Nearside Front Position lamp not working (4.2.1 (a) (ii))
Nearside Rear Position lamp not working (4.2.1 (a) (ii))
Nearside Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))
Offside Front Position lamp not working (4.2.1 (a) (ii))
Offside Rear Position lamp not working (4.2.1 (a) (ii))
Offside Rear fog lamp not working (4.5.1 (a) (ii))
Offside Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))
Both chassis corroded
Nearside Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))
Nearside Front Lower Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))
Nearside Rear Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))
Nearside rear inner lower panel corroded and holed
Offside Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))
Offside Front Lower Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))
Offside Rear Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))
Offside rear out rigger corroded and holed
Nearside Front Lower Suspension arm has slight play in a ball joint (2.4.G.2)
Nearside Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)
Offside Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)
Parking brake lever has little reserve travel (3.1.6b)
corrosion to underside of vehicle
Nearside Front suspension has slight play in a lower suspension ball joint (2.5.B.1a)
Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)
footbrake slightly longer than usual
out rigger corroded OSR inner arch
All position lamps not working (1.1.A.3b)
Nearside Headlamp aim beam image obviously incorrect (1.8.A.1b)
Offside Rear rear brake binding (3.7.B.1)
Offside Rear rear brake recording little or no effort (3.7.B.5a)
Offside Rear rear parking brake recording little or no effort (3.7.B.6a)
Parking brake lever has no reserve travel (3.1.6b)
Parking brake: efficiency below requirements (3.7.B.7)
Rear Brakes imbalanced across an axle Axle 2 (3.7.B.5b)
Registration plate lamp not working (1.1.C.1d)
Speedometer cannot be illuminated. (6.7.3)
Windscreen has a sticker or other obstruction encroaching by more than 10mm within zone 'A' Dash add on (8.3.1b)
Nearside Front suspension has slight play in a lower suspension ball joint (2.5.B.1a)
Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)
out rigger corroded OSR inner arch
All position lamps not working (1.1.A.3b)
Brake master cylinder/servo mounting prescribed area is excessively corroded under bonnet and inner wheel arch (3.6.C.3)
Nearside Front Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)
Nearside Front Seat belt retracting mechanism defective (5.2.5b)
Offside Rear fog lamp not working (1.3.2b)
Parking brake lever has no reserve travel (3.1.6b)
Parking brake: efficiency below requirements (3.7.B.7)
Registration plate lamp not working both (1.1.C.1d)
Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone 'A' (8.3.1e)
all general underbody,chassis and component corrosion
Nearside Rear Anti-roll bar has slight play in a pin/bush (2.4.G.2)
Nearside Rear Anti-roll bar linkage has slight play in a ball joint (2.4.G.2)
Nearside Rear Tyre worn close to the legal limit Inner edge (4.1.E.1)
Offside Rear Anti-roll bar linkage has slight play in a ball joint (2.4.G.2)
Offside Rear Rear wheel bearing has slight play (2.6.2)
Parking brake lever has little reserve travel (3.1.6b)
Nearside Rear Anti-roll bar has slight play in a pin/bush (2.4.G.2)
Nearside Rear Anti-roll bar linkage has slight play in a ball joint (2.4.G.2)
Nearside Rear Tyre worn close to the legal limit Inner edge (4.1.E.1)
Nearside Registration plate lamp not working (1.1.C.1d)
Offside Front position lamp(s) not working (1.1.A.3b)
Offside Rear Anti-roll bar linkage has slight play in a ball joint (2.4.G.2)
Offside Rear Rear wheel bearing has slight play (2.6.2)
Parking brake lever has little reserve travel (3.1.6b)
Brake load sensing valve seized (3.6.E.3)
Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)
Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)
Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded (3.6.C.3)
Offside Front Front position lamp(s) not working (1.1.A.3b)
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)
Offside Rear fog lamp not working (1.3.2b)
Parking brake lever has little reserve travel (3.1.6b)
Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)
all underside corrosion
nearside rear tyre worn on inner edge
Rear brake discs corroded
Nearside Rear Anti-roll bar rubber mounting deteriorated but not resulting in excessive movement (2.4.G.2)
Offside Rear Anti-roll bar rubber mounting deteriorated but not resulting in excessive movement (2.4.G.2)
Nearside Front suspension has slight play in a lower suspension ball joint (2.5.B.1a)
Nearside Rear Leaf spring has a slightly deteriorated anchor pin rubber bush not resulting in excessive movement (2.4.B.2)
Offside Front Tyre worn close to the legal limit (4.1.E.1)
Offside Rear Leaf spring has a slightly deteriorated anchor pin rubber bush not resulting in excessive movement (2.4.B.2)
Front Front suspension has slight movement at a wishbone pin or bush (2.5.A.1c)
Nearside Front Front suspension has slight play in a lower suspension ball joint (2.5.B.1a)
Nearside Rear Anti-roll bar linkage has slight play in a pin/bush (2.4.G.2)
Offside Front Headlamp not working on dipped beam (1.7.5a)
Offside Rear Anti-roll bar linkage has slight play in a pin/bush (2.4.G.2)
Oil leak
Rear Anti-roll bar linkage has slight play in a pin/bush (2.4.G.2)
Rear Brake pad(s) wearing thin (3.5.1g)
Rear Registration plate lamp not working (1.1.C.1d)
Front Front suspension has slight movement at a wishbone pin or bush (2.5.A.1c)
Nearside Front Front suspension has slight play in a lower suspension ball joint (2.5.B.1a)
Nearside Rear Anti-roll bar linkage has slight play in a pin/bush (2.4.G.2)
Offside Rear Anti-roll bar linkage has slight play in a pin/bush (2.4.G.2)
Oil leak
Rear Anti-roll bar linkage has slight play in a pin/bush (2.4.G.2)
Rear Brake pad(s) wearing thin (3.5.1g)
Nearside Front Lower Suspension arm has excessive play in a ball joint (2.4.G.2)
Nearside Front Lower Suspension arm rubber bush deteriorated resulting in excessive movement (2.4.G.2)
Nearside Rear Leaf spring has a deteriorated shackle pin rubber bush resulting in excessive movement (2.4.B.2)
Offside Front Headlamp not working on dipped beam (1.7.5a)
Offside Rear Leaf spring has a deteriorated anchor pin rubber bush resulting in excessive movement (2.4.B.2)
Offside Rear Leaf spring has a deteriorated shackle pin rubber bush resulting in excessive movement (2.4.B.2)
Registration plate lamp not working (1.1.C.1d)
Nearside Rear Leaf spring fractured (2.4.B.1a)
Nearside Rear Suspension has inadequate clearance with the bump stop (2.4.A.1a)
Nearside Registration plate lamp not working (1.1.C.1d)
Nearside Windscreen wiper does not clear the windscreen effectively (8.2.2)
Offside Headlamp not working on dipped beam (1.7.5a)
Offside Registration plate lamp not working (1.1.C.1d)
Windscreen has damage to the swept area in excess of a 40mm circle outside zone 'A' (8.3.1d)
Nearside Front Upper Suspension arm has excessive play in a pin/bush (2.4.G.2)
Nearside Registration plate lamp not working (1.1.5c)
Nearside Side repeater incorrect colour (1.4.A.2f)
Offside Registration plate lamp not working (1.1.5c)
Offside Side repeater incorrect colour (1.4.A.2f)
Parking brake: parking brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.7)
How Reliable is the Iveco Daily?
Based on 817,098 MOT tests across 76,231 vehicles.
Top MOT Failure Points
Don't risk it. Know before you buy.
Not all vehicle check providers are the same. Some don't offer a data guarantee, which means if their information is wrong, you're on your own. Every CarVerify report is backed by a £30,000 finance data guarantee.
WM05 PJM is a 2005 Iveco Daily in Blue with a 2,300cc diesel engine. This vehicle has been through 30 MOT tests with a personal pass rate of 56.7%.
Across all 2005 Iveco Daily models, the average MOT pass rate is 64.0% with a typical mileage of 112,037 miles. This particular vehicle has a lower pass rate than the average for its year, which may indicate maintenance issues worth investigating.
The most common reason a Iveco Daily fails its MOT is parking brake: efficiency below requirements, accounting for 54,319 recorded failures. If you're considering buying WM05 PJM, it's worth having these areas checked by a mechanic before committing.
The Iveco Daily typically stays on UK roads for around 30 years. At 21 years old, this Iveco Daily is well into its expected lifespan but still has years ahead.
Frequently Asked Questions
How do I check the history of WM05 PJM?
You can check the full history of WM05 PJM by running a full vehicle check. This shows you finance, stolen, write-off, MOT history, mileage records and more.
What year was WM05 PJM registered?
WM05 PJM is a 2005 Iveco Daily, first registered on 1 March 2005.
Is WM05 PJM safe to buy?
The MOT history for WM05 PJM shows 30 tests with a 56.7% pass rate. To check for outstanding finance, stolen markers, write-off history and mileage discrepancies, run a full vehicle check.
Does WM05 PJM have outstanding finance?
Finance checks require a premium vehicle report. This checks against all major UK finance providers to see if there is any outstanding finance on WM05 PJM. If you buy a car with outstanding finance, the finance company can repossess it.
No warranty or guarantee of accuracy is provided for any free data on this page. The data guarantee applies only to information obtained through the purchase of a full check.