2004 Subaru Forester

Nearside Rear Lower Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Nearside Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Rear Upper Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Lower Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Offside Rear Upper Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h))

Nearside Rear Lower Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Nearside Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Rear Upper Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Lower Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Offside Rear Upper Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

EML on

Front All ball joint boots cracking up

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Rear Subframe mounting prescribed area damaged but not considered excessive (5.3.6 (a) (i))

Sill covers fitted

Nearside Rear Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Rear Suspension component mounting prescribed area damaged but not considered excessive (5.3.6 (a) (i))

Offside Rear Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Suspension component mounting prescribed area damaged but not considered excessive (5.3.6 (a) (i))

Offside Rear Upper Suspension component mounting prescribed area damaged but not considered excessive (5.3.6 (a) (i))

Rear Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Bonnet primary retaining device ineffective (3.1 (c))

Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h))

Nearside Rear Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Upper Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Rear Subframe mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Nearside Rear Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Rear Subframe mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Emissions not tested (8.2.1.2 (d))

Front Exhaust has a major leak of exhaust gases (6.1.2 (a))

Front Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Nearside Rear Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Rear Subframe mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Front Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Nearside Front Body panel slightly loose (6.2.1 (a) (i))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Rear Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Offside Front Position lamp not working (4.2.1 (a) (ii))

Offside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i))

Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii))

Nearside Front Wheel bearing so rough it is likely to overheat or break up (5.1.3 (b) (ii)) DANGEROUS

Offside Front Lower Suspension arm ball joint likely to become detached (5.3.4 (a) (ii)) DANGEROUS

Front Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Nearside Front Body panel slightly loose (6.2.1 (a) (i))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Rear Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Nearside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Offside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Emissions not tested (8.2.1.2 (d))

Exhaust has a major leak of exhaust gases (6.1.2 (a))

Nearside Front Position lamp not working (4.2.1 (a))

Nearside Headlamp aim too high (4.1.2 (a))

Offside Front Wheel bearing rough when rotated (5.1.3 (b) (i))

Offside Headlamp aim too high (4.1.2 (a))

Rear Sub-frame corroded and seriously weakened x2 (5.3.3 (b) (i))

Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Windscreen washer provides insufficient washer liquid (3.5 (a))

Nearside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Offside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Offside Front Anti-roll bar linkage has slight play in a ball joint (2.4.G.2)

Nearside Front Mechanical brake component has restricted free movement (3.5.1k)

Nearside Rear Anti-roll bar linkage has excessive play in a ball joint (2.4.G.2)

Nearside Rear Brake hose ferrule excessively corroded (3.6.B.4e)

Offside Rear Brake hose ferrule excessively corroded (3.6.B.4e)

Offside Rear Brake pipe excessively corroded (3.6.B.2c)

front brake disc in poor state, rust

Nearside Rear Anti-roll bar linkage has slight play in a pin/bush (2.4.G.2)

Offside Rear Brake pipe slightly corroded (3.6.B.2c)

Nearside Front Front position lamp(s) not working (1.1.A.3b)

Nearside Front Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Front Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Rear Brake pipe slightly corroded (3.6.B.2c)

Front Brake pad(s) wearing thin (3.5.1g)

Front Brake pad(s) wearing thin (3.5.1g)

Offside Registration plate lamp not working (1.1.C.1d)

Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Exhaust emissions carbon monoxide content after 2nd fast idle excessive (7.3.D.3)

Nearside Front Anti-roll bar has excessive play in a ball joint (2.4.G.2)

Nearside Front Brake pad(s) less than 1.5 mm thick (3.5.1g)

Nearside Front front brake binding (3.7.B.1)

Offside Front Anti-roll bar has excessive play in a ball joint (2.4.G.2)

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Front Brake pad(s) wearing thin (3.5.1g)

front discs in poor condition

unable to fully check sills,fuel filler neck and brake pipes as they are hidden from view/or covered.

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)