2000 Renault Master

Nearside Front Brake pipe excessively corroded x2 (1.1.11 (c))

Nearside Front Wheel bearing has excessive play (5.1.3 (a) (i))

Nearside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c))

Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting LEAF SPRING MOUNT (FRONT) (6.2.2 (d) (i))

Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting LEAF SPRING MOUNT (REAR) (6.2.2 (d) (i))

Offside Front Suspension arm pin or bush excessively worn FRONT BUSH (5.3.4 (a) (i))

Offside Front Wheel bearing has excessive play (5.1.3 (a) (i))

Offside Rear Parking brake inoperative on one side (1.4.1 (a))

Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting LEAF SPRING MOUNT (REAR) (6.2.2 (d) (i))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Service brake efficiency below requirements (1.2.2 (a) (i))

Nearside Front Brake hose ferrule excessively corroded and likely to fail x2 (1.1.12 (f) (ii)) DANGEROUS

Central FUEL TANK STRAP CORRODED

Central Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Nearside Front Upper Shock absorbers has a slightly worn bush (5.3.2 (c))

Offside Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Offside Front Upper Shock absorbers has a slightly worn bush (5.3.2 (c))

Rear BUMP STOPS MISSING

Nearside Front Shock absorbers has a slightly worn bush (5.3.2 (c))

Nearside Front Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security inner floor section (6.2.2 (d) (i))

Front Exhaust has a major leak of exhaust gases (6.1.2 (a))

Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i))

Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i))

Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i))

Windscreen washer provides insufficient washer liquid (3.5 (a))

Nearside Front Inner Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security (6.2.2 (d) (i))

Nearside Front Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Offside Front Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security (6.2.2 (d) (i))

Rear Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Fuel system component leaking (6.1.3 (b) (i))

Horn not working (7.7 (a))

Offside Front Suspension arm insecurely attached (5.3.3 (a) (i))

Nearside Front Inner Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security (6.2.2 (d) (i))

Nearside Front Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Offside Front Vehicle structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security (6.2.2 (d) (i))

Rear Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Integral body structure is corroded but structural rigidity is not significantly reduced corrosion on both inner sills/various parts of underbody etc (6.1.1 (c) (i))

Rear Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. also handbrake imbalance (1.2.1 (b) (i))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Service brake efficiency below requirements (1.2.2 (a) (i))

Integral body structure is corroded but structural rigidity is not significantly reduced corrosion on both inner sills/various parts of underbody etc (6.1.1 (c) (i))

Brake disc worn, pitted or scored, but not seriously weakened both rear discs rusty on inner faces (1.1.14 (a) (ii))

Brake pad(s) wearing thin front pads75% worn (1.1.13 (a) (ii))

Integral body structure is corroded but structural rigidity is not significantly reduced slight corrosion on various parts of underbody/inner sills etc (6.1.1 (c) (i))

Offside Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Oil leak, but not excessive slight oil leak on engine (8.4.1 (a) (i))

Rear Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. also handbrake imbalance o/s rear (1.2.1 (b) (i))

Service brake requirements only just met. It would appear that the braking system requires adjustment or repair also handbrake effort (1.2.1 (c))

Sub-frame corroded but not seriously weakened slight corrosion on both front/rear subframes/suspension assemblies etc (5.3.3 (b) (i))

Brake disc worn, pitted or scored, but not seriously weakened both rear discs rusty on faces (1.1.14 (a) (ii))

Integral body structure is corroded but structural rigidity is not significantly reduced corrosion on various parts of underbody/chassis/inner sills etc (6.1.1 (c) (i))

Rear Service brake requirements only just met. It would appear that the braking system requires adjustment or repair also handbrake only just passed test advise attention (1.2.1 (c))

both fuel tank straps corroding

n/s rear axle bump stop missing and o/s deteriorating

Nearside Rear Leaf spring shackle bracket corroded and seriously weakened bracket corroded through (5.3.1 (b) (i))

Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch to outrigger (behind rear wheel) corroded through (6.1.1 (c) (i))

Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength n/s and o/s rear outriggers corroded through above both rear spring swinging shackle brackets/hangers (5.3.6 (a) (i))

Brake disc worn, pitted or scored, but not seriously weakened both rear discs rusty on inner faces advise attention (1.1.14 (a) (ii))

Integral body structure is corroded but structural rigidity is not significantly reduced corrosion on various parts of underbody/chassis/inner sills etc (6.1.1 (c) (i))

Offside Rear Leaf spring shackle bracket corroded but not seriously weakened advise attention (see failure on opposite bracket) (5.3.1 (b) (i))

Rear Service brake requirements only just met. It would appear that the braking system requires adjustment or repair also handbrake effort only just passed test advise attention (1.2.1 (c))

both fuel tank straps corroding

n/s rear axle bumpstop deteriorating and o/s missing

Integral body structure is corroded but structural rigidity is not significantly reduced corrosion on various parts of rear underbody/chassis/crossmembers etc (6.1.1 (c) (i))

Offside Front Wheel bearing has slight play (5.1.3 (a) (i))

n/s rear axle bump stop deteriorating

o/s rear axle bump stop missing

rear axle footbrake effort only just passed test

Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting both front jacking points corroded through (behind front wheels) (6.2.2 (d) (i))

Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting n/s rear bracing panel corroded through between outrigger and rear crossmember (6.2.2 (d) (i))

Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting o/s inner sill corroded through centre and rear (6.2.2 (d) (i))

Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting o/s rear outer sill corroded through (6.2.2 (d) (i))

Offside Rear Rear fog lamp not working (4.5.1 (a) (ii))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Service brake efficiency below requirements (1.2.2 (a) (i))

Integral body structure is corroded but structural rigidity is not significantly reduced corrosion on various parts of rear underbody/chassis/crossmembers etc (6.1.1 (c) (i))

Offside Front Wheel bearing has slight play (5.1.3 (a) (i))

n/s rear axle bump stop deteriorating

o/s rear axle bump stop missing

Integral body structure is corroded but structural rigidity is not significantly reduced corrosion on both inner sills (6.1.1 (c) (i))

Integral body structure is corroded but structural rigidity is not significantly reduced corrosion on o/s outer sill (6.1.1 (c) (i))

Integral body structure is corroded but structural rigidity is not significantly reduced corrosion on various parts of underbody (6.1.1 (c) (i))

Sub-frame corroded but not seriously weakened corrosion on both subframes/axle and assemblies etc (5.3.3 (b) (i))

rear axle footbrake/handbrake efforts only just passed test

reverse lights n/w

Front registration plate deteriorated but not likely to be misread (6.3.1d)

Rear Brake load sensing valve defective but function not impaired (3.6.E.3)

Battery insecure (1.9.1)

Front Exhaust has a major leak of exhaust gases (7.1.2)

Nearside Front Brake pipe excessively corroded (3.6.B.2c)

Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering outrigger (6.1.A.1)

Nearside Steering rack gaiter split (2.2.D.2d)

Nearside rear parking brake recording little or no effort (3.7.B.6a)

Offside Front Body has a sharp edge caused by corrosion outer step sill (6.1.C.1)

Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering outrigger (6.1.A.1)

Offside Track rod end ball joint has excessive play (2.2.B.1f)

Parking brake: efficiency below requirements (3.7.B.7)

Front registration plate deteriorated but not likely to be misread (6.3.1d)

Rear discs inner faces badly corroded

Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

SURFACE CORROSION TO UNDERBODY COMPONENTS

Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

Brake load sensing valve seized (3.6.E.3)

Nearside Front Direction indicator not working (1.4.A.2c)

Offside Rear reflector missing (1.5.1a)

Parking brake: efficiency below requirements (3.7.B.7)

Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

SURFACE CORROSION TO UNDERBODY COMPONENTS

Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

general vehicle corrosion

Nearside Front wheel bearing has slight play (2.5.A.3c)

Offside Front wheel bearing has slight play (2.5.A.3c)

Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

rear brake disc's badly corroded

Horn not working (1.6.2a)

Nearside Registration plate lamp not working (1.1.C.1d)

Offside Headlamp aim beam image obviously incorrect (1.8.A.1b)

Parking brake: efficiency below requirements (3.7.B.7)

Service brake: efficiency below requirements (3.7.B.7)

rear brake disc's badly corroded

Brake pipe excessively corroded (3.6.B.2c)

Offside Front Front position lamp(s) excessively deteriorated so that it is not visible from a reasonable distance (1.1.A.3d)

Rear Registration plate lamp not working (1.1.C.1d)

Windscreen washer provides insufficient washer liquid (8.2.3)

Nearside Parking brake: parking brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.7)

Nearside Rear Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Rear Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

clutch pedel rubber

Brake pedal anti-slip provision missing (3.3.A.1b)

Nearside rear brake recording little or no effort (3.7.B.5a)

Nearside rear parking brake recording little or no effort (3.7.B.6a)

Offside rear brake recording little or no effort (3.7.B.5a)

Parking brake: efficiency below requirements (3.7.B.7)

Rear registration plate character(s) likely to be misread (6.3.4b)

Service brake: efficiency below requirements (3.7.B.7)

Windscreen washer provides insufficient washer liquid (8.2.3)

Nearside Rear Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Rear Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)

clutch pedel rubber

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Brake pedal anti-slip provision missing (3.3.A.1b)

Brakes imbalanced across an axle (3.7.D.2c)

Front Windscreen washer provides insufficient washer liquid (8.2.3)

Front Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Front Headlamp not working on dipped beam (1.7.5a)

Offside Front Steering system has excessive free play detected at the steering wheel (steering rack fitted) (2.2.A.1b)

Parking brake: efficiency below requirements (3.7.D.4)

Rear Registration plate lamp not working (1.1.C.1d)

Service brake: efficiency below requirements (3.7.D.4)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Brake hydraulic reservoir fluid level below minimum level (3.6.G.1b)

Front Brake pad(s) less than 1.5 mm thick (3.5.1g)

Nearside Front Headlamp not in good working order adversely affecting beam image (1.2.4a)

Offside Front Front position lamp(s) not working (1.1.A.3b)

Offside Front Steering pivot point has excessive play (2.2.B.1g)

Rear Brake pad(s) less than 1.5 mm thick (3.5.1g)

Brake load sensing valve linkage seized (3.6.E.3)

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Parking brake lever has no reserve travel (3.1.6b)

Parking brake: efficiency below requirements (3.7.B.7)