2000 Daewoo Matiz

Exhaust emissions carbon monoxide content after 2nd fast idle excessive (7.3.D.3)

Exhaust emissions carbon monoxide content at idle excessive (7.3.D.4)

Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Outer sill (6.1.B.2)

Nearside Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2)

Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Outer sill (6.1.B.2)

Offside Rear rear brake recording little or no effort (3.7.B.5a)

Rear Brakes imbalanced across an axle Axle 2 (3.7.B.5b)

Front position lamp(s) has a product on the light source but not adversely affecting light output (1.1.A.3d)

Oil leak at engine

Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)

Oil Leak.

Nearside Headlamp has a product on the lens but not seriously reducing light output (1.7.5a)

Nearside Rear Brake pipe slightly corroded (3.6.B.2c)

Offside Headlamp has a product on the lens but not seriously reducing light output (1.7.5a)

Parking brake lever has little reserve travel (3.1.6b)

Rear registration plate deteriorated but not likely to be misread (6.3.1d)

Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)

Exhaust emissions carbon monoxide content after 2nd fast idle excessive (7.3.D.3)

Exhaust emissions carbon monoxide content at idle excessive (7.3.D.4)

Nearside Rear Inner Suspension component mounting prescribed area is excessively corroded arch (2.4.A.3)

Nearside Track rod end ball joint has excessive play (2.2.B.1f)

Offside Rear Inner Suspension component mounting prescribed area is excessively corroded arch (2.4.A.3)

Offside rear brake recording little or no effort (3.7.B.5a)

Offside rear parking brake recording little or no effort (3.7.B.6a)

Rear Brakes imbalanced across an axle Axle 2 (3.7.B.5b)

Nearside Headlamp has a product on the lens but not seriously reducing light output (1.7.5a)

Nearside Rear Brake pipe slightly corroded (3.6.B.2c)

Offside Headlamp has a product on the lens but not seriously reducing light output (1.7.5a)

Oil Leak.

Parking brake lever has little reserve travel (3.1.6b)

Rear registration plate deteriorated but not likely to be misread (6.3.1d)

Windscreen has damage to an area less than a 10mm circle within zone 'A' (8.3.1a)

Nearside Front Lower Suspension arm ball joint dust cover deteriorated, but preventing the ingress of dirt (2.4.G.2)

Nearside Headlamp has a product on the lens but not seriously reducing light output (1.7.5a)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Headlamp has a product on the lens but not seriously reducing light output (1.7.5a)

Oil leak

Play in steering rack inner joint(s)

Exhaust emissions Lambda reading after 2nd fast idle outside specified limits (7.3.D.3)

Exhaust has a major leak of exhaust gases (7.1.2)

Front Windscreen washer provides insufficient washer liquid (8.2.3)

Nearside Front Lower Suspension arm ball joint dust cover deteriorated, but preventing the ingress of dirt (2.4.G.2)

Nearside Headlamp has a product on the lens but not seriously reducing light output (1.7.5a)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Headlamp has a product on the lens but not seriously reducing light output (1.7.5a)

Oil leak

Play in steering rack inner joint(s)

Rear Service brake: service brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.7)

Offside Front Lower Suspension arm has excessive play in a ball joint (2.4.G.2)

Offside Outer Seat belt anchorage prescribed area is excessively corroded (5.2.6)

Supplementary Restraint System warning lamp indicates a fault (5.4.2)

Items removed from driver's view prior to test

Exhaust emissions carbon monoxide content after 2nd fast idle excessive (7.3.D.3)

Nearside Registration plate lamp not working (1.1.C.1d)

Offside Registration plate lamp not working (1.1.C.1d)

Front Brake pipe slightly corroded (3.6.B.2c)

Rear Exhaust has a minor leak of exhaust gases (7.1.2)

Exhaust emissions Lambda reading after 2nd fast idle outside specified limits (7.3.D.3)

Headlamp aim too low (1.8)

Front Brake pipe slightly corroded (3.6.B.2c)

Rear Exhaust has a minor leak of exhaust gases (7.1.2)

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)

corrosion showing on rear suspension components

Front Windscreen washer provides insufficient washer liquid (8.2.3)

Nearside Front Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a)

Nearside Rear Suspension component mounting prescribed area is excessively corroded (2.4.A.3)

Offside Front Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a)

Offside Front Seat belt anchorage prescribed area is excessively corroded (5.2.6)

Offside Front Track rod end ball joint has excessive play (2.2.B.1f)

Rear Exhaust emissions Lambda reading after 2nd fast idle outside specified limits (7.3.D.3)

Rear Exhaust emissions carbon monoxide content after 2nd fast idle excessive (7.3.D.3)

Rear Exhaust system not adequately supported (7.1.1)

Front Front position lamp(s) slightly discoloured (1.1.A.3e)

n/s/f steel brake pipe corroded

o/s/r inner sill heavy corrosion

Front constant velocity joint gaiter deteriorated (2.5.C.1a)

Offside Front Lower Suspension arm has slight play in a ball joint (2.4.G.2)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Rear wheel bearing has slight play (2.6.2)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)