2001 Toyota Yaris

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Top shock mount (5.3.6 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Trailing arm bush. (5.3.6 (a) (i))

Nearside Steering locking device missing Track rod end (2.1.3 (d))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Top shock mount (5.3.6 (a) (i))

Offside Steering locking device missing Track rod end (2.1.3 (d))

Front Registration plate deteriorated but not likely to be misread (0.1 (b))

Nearside Rear Fuel Pipe/s corroded Filler pipes ()

Nearside Rear Shock absorbers has light misting of oil (5.3.2 (b))

Nearside Rear Suspension arm pin or bush worn but not resulting in excessive movement Trailing arm (5.3.4 (a) (i))

Offside Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Offside Rear Suspension arm pin or bush worn but not resulting in excessive movement Trailing arm (5.3.4 (a) (i))

Nearside Rear Fuel Pipe/s corroded filler neck pipes ()

Nearside Rear Suspension arm pin or bush worn but not resulting in excessive movement trailing arm bush (5.3.4 (a) (i))

Offside Rear Suspension arm pin or bush worn but not resulting in excessive movement trailing arm bush (5.3.4 (a) (i))

Rear Registration plate deteriorated but not likely to be misread (0.1 (b))

Nearside Rear Brake pipe excessively corroded (1.1.11 (c))

Nearside Rear Brake pipe leaking on a hydraulic braking system brake test aborted (1.1.11 (b) (ii)) DANGEROUS

Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) DANGEROUS

Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) DANGEROUS

Nearside Rear Fuel Pipe/s corroded filler neck pipes ()

Nearside Rear Suspension arm pin or bush worn but not resulting in excessive movement trailing arm bush (5.3.4 (a) (i))

Offside Rear Suspension arm pin or bush worn but not resulting in excessive movement trailing arm bush (5.3.4 (a) (i))

Rear Registration plate deteriorated but not likely to be misread (0.1 (b))

Front Registration plate deteriorated but not likely to be misread (0.1 (b))

Nearside Front Shock absorbers has light misting of oil (5.3.2 (b))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Central Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Nearside Front Shock absorbers has light misting of oil (5.3.2 (b))

Nearside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Nearside Front Shock absorbers light misting of oil or has limited damping effect (5.3.2 (b))

Rear Inner Integral body structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security both sides inner side sill rusted (6.2.2 (d) (i))

Brake lever has insufficient reserve travel (1.1.2 (a))

Emissions not tested not tested as exhaust is blowing (8.2.1.2 (d))

Rear Exhaust has a major leak of exhaust gases middle pipe to rear box blowing just before it joins (6.1.2 (a))

Nearside Front Shock absorbers light misting of oil or has limited damping effect (5.3.2 (b))

Rear Inner Integral body structure or chassis corroded within 30cm of a mounting, but not seriously affecting overall security both sides inner side sill rusted (6.2.2 (d) (i))

Nearside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Central Stop lamp(s) not working (4.3.1 (a) (ii))

Offside Rear Brake pipe excessively corroded (1.1.11 (c))

Nearside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Rear Exhaust has a minor leak of exhaust gases (7.1.2)

high level brake light not working

Windscreen washer provides insufficient washer liquid (8.2.3)

Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)