2000 Subaru Legacy

Hazard warning switch faulty (1.4.B.1d)

Nearside Front Anti-roll bar has excessive play in a pin/bush (2.4.G.2)

Nearside Front Brake pad(s) less than 1.5 mm thick (3.5.1g)

Nearside Front Steering rack gaiter split (2.2.D.2d)

Nearside Front front brake binding (3.7.B.1)

Nearside Rear Registration plate lamp not working (1.1.C.1d)

Nearside Rear position lamp(s) not working (1.1.A.3b)

Nearside Stop lamp not working (1.2.1b)

Offside Front Brake pad(s) less than 1.5 mm thick (3.5.1g)

Offside Front Steering rack gaiter split (2.2.D.2d)

Offside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a)

Offside Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a)

Offside Front position lamp(s) not working (1.1.A.3b)

Offside Rear Seat belt anchorage prescribed area is excessively corroded (5.2.6)

Front Exhaust has a minor leak of exhaust gases (7.1.2)

Nail in nearside rear tyre

Offside Front Shock absorber has a light misting of oil (2.7.3)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Centre Rear Statutory seat belt missing (5.1.1)

Centre Steering pivot point has excessive play (2.2.B.1g)

Exhaust has a major leak of exhaust gases (7.1.2)

Exhaust system not adequately supported (7.1.1)

Nearside Front Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a)

Nearside Obligatory mirror seriously deteriorated, affecting the rear view (8.1.2a)

Nearside Rear Stop lamp not working (1.2.1b)

Offside Drag link end ball joint has excessive play (2.2.B.1f)

Offside Front Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a)

Offside Rear Anti-roll bar has excessive play in a pin/bush (2.4.G.2)

Offside Rear Stop lamp not working (1.2.1b)

Parking brake lever has no reserve travel (3.1.6b)

Centre Exhaust has part of the system excessively deteriorated (7.1.1a)

Front Exhaust system not adequately supported (7.1.1)

Nearside Front Anti-roll bar has excessive play in a ball joint (2.4.G.2)

Nearside Front Front constant velocity joint gaiter split (2.5.C.1a)

Nearside Front Suspension arm rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Nearside Rear Anti-roll bar has excessive play in a ball joint (2.4.G.2)

Nearside Rear Trailing arm rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Nearside Stop lamp not working (1.2.1b)

Offside Front Shock absorber has a serious fluid leak (2.7.3)

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Stop lamp not working (1.2.1b)

Inner Front Brake pad(s) less than 1.5 mm thick (3.5.1g)

Nearside Rear Shock absorber has a serious fluid leak (2.7.3)

Front Service brake grabbing slightly (3.7.C.2)

Nearside Rear Anti-roll bar linkage has slight play in a ball joint (2.4.G.2)

Centre Rear Exhaust has a major leak of exhaust gases (7.1.2)

Nearside Front Windscreen wiper does not clear the windscreen effectively (8.2.2)

Nearside Rear Anti-roll bar missing (2.4.G.1)

Offside Front Windscreen wiper does not clear the windscreen effectively (8.2.2)

Offside Stop lamp not working (1.2.1b)

Nearside Rear Anti-roll bar linkage has excessive play in a ball joint (2.4.G.2)

Nearside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Nearside Rear Brake pad(s) less than 1.5 mm thick (3.5.1g)

Nearside Registration plate lamp not working (1.1.5c)

Offside Front Brake pad(s) less than 1.5 mm thick (3.5.1g)

Offside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Offside Registration plate lamp not working (1.1.5c)

Nearside Headlamp aim too low (1.8)

Offside Headlamp not working on dipped beam (1.7.5a)

Rear Stop lamp not working (1.2.1b)

Registration plate lamp not working (1.1.5c)

Offside Rear Anti-roll bar linkage insecure (2.4.G.1)

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)