MOT Status
ExpiredMileage
134,008 miAbove average mileage for this year
Not all car check providers offer a guarantee. Don't risk buying from services that can't back their data. CarVerify reports include a £30,000 finance data guarantee.
Vehicle Details
All premium checks include
50+ data pointsMOT History
Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))
all underside of vehicle has corrosion but not to excess
Nearside Front Brake pipe excessively corroded (1.1.11 (c))
Nearside Headlamp aim too low (4.1.2 (a))
Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i))
Offside Headlamp not working on dipped beam (4.1.1 (a) (ii))
Offside Stop lamp(s) not working (4.3.1 (a) (ii))
Parking brake efficiency below requirements (1.4.2 (a) (i))
Nearside Front Brake pad(s) less than 1.5 mm thick (1.1.13 (a) (ii)) DANGEROUS
Offside Rear Lower Suspension component mounting prescribed area is corroded but not considered excessive outer sill (5.3.6 (a) (i))
Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))
all underside of vehicle has corrosion but not to excess
Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))
Nearside Rear Lower Suspension component mounting prescribed area is corroded but not considered excessive outer sill (5.3.6 (a) (i))
Offside Rear Lower Suspension component mounting prescribed area is corroded but not considered excessive inner sill (5.3.6 (a) (i))
Offside Rear Lower Suspension component mounting prescribed area is corroded but not considered excessive inner sills (5.3.6 (a) (i))
Exhaust emissions exceed default limit of 1.5m-1 (8.2.2.2 (b))
Nearside Headlamp aim too low (4.1.2 (a))
Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i))
Offside Front Lower Suspension component ball joint excessively worn outer (5.3.4 (a) (i))
Offside Headlamp not working on dipped beam (4.1.1 (a) (ii))
Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i))
Offside Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))
Parking brake efficiency below requirements (1.4.2 (a) (i))
Windscreen washer provides insufficient washer liquid (3.5 (a))
Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))
Nearside Rear Lower Suspension component mounting prescribed area is corroded but not considered excessive outer sill (5.3.6 (a) (i))
Offside Rear Lower Suspension component mounting prescribed area is corroded but not considered excessive inner sill (5.3.6 (a) (i))
Offside Rear Lower Suspension component mounting prescribed area is corroded but not considered excessive inner sills (5.3.6 (a) (i))
Offside Front Lower Suspension component ball joint has slight play outer (5.3.4 (a) (i))
Emissions not tested due to hole in exhaust (8.2.2.2 (e))
Exhaust has a major leak of exhaust gases (6.1.2 (a))
Nearside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced oute sill (7.1.1 (a) (i))
Offside Headlamp not working on dipped beam (4.1.1 (a) (ii))
Parking brake efficiency below requirements (1.4.2 (a) (i))
Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))
Offside Front Lower Suspension component ball joint has slight play outer (5.3.4 (a) (i))
Exhaust emissions exceed manufacturer's specified limit Plate 3.0 Reading 4.96 (8.2.2.2 (a))
Front passenger door cannot be opened from inside the vehicle (6.2.3 (a))
Nearside Front Anti-roll bar pin or bush excessively worn D BUSH (5.3.4 (a) (i))
Nearside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))
Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i))
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Jack point (5.3.6 (a) (i))
Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i))
Nearside Stop lamp(s) not working (4.3.1 (a) (ii))
Offside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))
Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i))
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Jack point (5.3.6 (a) (i))
Offside Headlamp not working on dipped beam (4.1.1 (a) (ii))
Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill x2 (5.3.6 (a) (i))
Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))
Offside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))
Steering rack has slight free play detected at steering wheel (2.3 (a) (i))
Windscreen damaged but not adversely affecting driver's view (3.2 (a) (i))
Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))
Nearside Front Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))
Nearside Front Suspension component pin or bush slightly worn (5.3.4 (a) (i))
Offside Front Lower Suspension component ball joint has slight play outer (5.3.4 (a) (i))
Offside Front Suspension component pin or bush slightly worn (5.3.4 (a) (i))
Windscreen damaged but not adversely affecting driver's view (3.2 (a) (i))
Offside Front Brake pipe excessively corroded (1.1.11 (c))
Offside Front Upper Macpherson strut top bush or bearing has excessive wear or free play (5.3.4 (a) (i))
Offside Rear Brake pad(s) less than 1.5 mm thick (1.1.13 (a) (ii)) DANGEROUS
Nearside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))
Nearside Front Suspension arm corroded but not seriously weakened (5.3.3 (b) (i))
Nearside Front Suspension component pin or bush slightly worn (5.3.4 (a) (i))
Offside Front Lower Suspension component ball joint has slight play outer (5.3.4 (a) (i))
Offside Front Suspension component pin or bush slightly worn (5.3.4 (a) (i))
Windscreen damaged but not adversely affecting driver's view (3.2 (a) (i))
2nd stage bonnet catch seized
Brake pad warning wires detached but all pads visable and good
Drivers door check strap snapped off
N/s front shocker has slight weep of oil
Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))
Nearside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))
Nearside Vehicle structure is corroded but structural rigidity is not significantly reduced By n/s rear front mounting suspension arm (6.1.1 (c) (i))
Offside Front Brake hose slightly chafed (1.1.12 (b) (i))
Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))
Suspension arm pin or bush worn but not resulting in excessive movement both front (5.3.4 (a) (i))
Windscreen damaged but not adversely affecting driver's view (3.2 (a) (i))
spare wheel defective
Nearside Brake pipe excessively corroded Front too back marked yellow (1.1.11 (c))
Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))
Nearside Stop lamp(s) not working (4.3.1 (a) (ii))
Offside Headlamp not working on dipped beam (4.1.1 (a) (ii))
Offside Headlamp not working on main beam (4.1.1 (a) (ii))
Offside Front Anti-roll bar linkage ball joint likely to become detached (5.3.4 (a) (ii)) DANGEROUS
2nd stage bonnet catch seized
Brake pad warning wires detached but all pads visable and good
Drivers door check strap snapped off
N/s front shocker has slight weep of oil
Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))
Nearside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))
Nearside Vehicle structure is corroded but structural rigidity is not significantly reduced By n/s rear front mounting suspension arm (6.1.1 (c) (i))
Offside Front Brake hose slightly chafed (1.1.12 (b) (i))
Offside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))
Suspension arm pin or bush worn but not resulting in excessive movement both front (5.3.4 (a) (i))
Windscreen damaged but not adversely affecting driver's view (3.2 (a) (i))
spare wheel defective
Nearside Rear Brake pipe slightly corroded (3.6.B.2c)
Offside Rear Lower Suspension component mounting prescribed area is corroded but not considered excessive outer sill (2.4.A.3)
Offside Headlamp not working on dipped beam (1.7.5a)
Nearside Rear Brake pipe slightly corroded (3.6.B.2c)
Offside Rear Lower Suspension component mounting prescribed area is corroded but not considered excessive outer sill (2.4.A.3)
Nearside Rear Inner Suspension component mounting prescribed area is excessively corroded Sill (2.4.A.3)
Offside Rear Inner Suspension component mounting prescribed area is excessively corroded Sill (2.4.A.3)
Service brake: efficiency below requirements (3.7.B.7)
Nearside Front Tyre has a tear, caused by separation or partial failure of its structure (4.1.D.1b) DANGEROUS
Nearside Front Tyre worn close to the legal limit (4.1.E.1)
Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)
Offside Headlamp not working on main beam (1.7.5a)
Offside Inner Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a)
Parking brake: efficiency below requirements (3.7.B.7)
Nearside Front Tyre worn close to the legal limit (4.1.E.1)
Rear Service brake: service brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.7)
Nearside Rear Lower Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Offside Front Tyre worn close to the legal limit (4.1.E.1)
Offside Rear Lower Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)
Brakes imbalanced across an axle (3.7.B.5b) DANGEROUS
Nearside Front Brake pad(s) less than 1.5 mm thick (3.5.1g)
Nearside Rear Brake pad(s) less than 1.5 mm thick (3.5.1g)
Offside Rear Brake pad(s) less than 1.5 mm thick (3.5.1g)
Parking brake: efficiency below requirements (3.7.B.7) DANGEROUS
Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)
Windscreen has damage to an area less than a 40mm circle outside zone 'A' (8.3.1d)
Front Brake hose excessively deteriorated (3.6.B.4d)
How Reliable is the Mercedes-benz Vito?
Based on 2,011,702 MOT tests across 164,434 vehicles.
Top MOT Failure Points
Don't risk it. Know before you buy.
Not all vehicle check providers are the same. Some don't offer a data guarantee, which means if their information is wrong, you're on your own. Every CarVerify report is backed by a £30,000 finance data guarantee.
X814 EBY is a 2000 Mercedes-benz Vito in White with a 2,151cc diesel engine. This vehicle has been through 26 MOT tests with a personal pass rate of 57.7%.
Across all 2000 Mercedes-benz Vito models, the average MOT pass rate is 62.9% with a typical mileage of 111,462 miles. This particular vehicle has a lower pass rate than the average for its year, which may indicate maintenance issues worth investigating.
The most common reason a Mercedes-benz Vito fails its MOT is parking brake: efficiency below requirements, accounting for 49,564 recorded failures. If you're considering buying X814 EBY, it's worth having these areas checked by a mechanic before committing.
The Mercedes-benz Vito typically stays on UK roads for around 29 years. At 26 years old, this Mercedes-benz Vito is approaching the upper end of the typical lifespan for this model.
Frequently Asked Questions
How do I check the history of X814 EBY?
You can check the full history of X814 EBY by running a full vehicle check. This shows you finance, stolen, write-off, MOT history, mileage records and more.
What year was X814 EBY registered?
X814 EBY is a 2000 Mercedes-benz Vito, first registered on 1 September 2000.
Is X814 EBY safe to buy?
The MOT history for X814 EBY shows 26 tests with a 57.7% pass rate. To check for outstanding finance, stolen markers, write-off history and mileage discrepancies, run a full vehicle check.
Does X814 EBY have outstanding finance?
Finance checks require a premium vehicle report. This checks against all major UK finance providers to see if there is any outstanding finance on X814 EBY. If you buy a car with outstanding finance, the finance company can repossess it.
No warranty or guarantee of accuracy is provided for any free data on this page. The data guarantee applies only to information obtained through the purchase of a full check.