2001 Toyota Yaris

Front front lower sub frame and lower arms have corrosion

UNDERSIDE, none specific corrosion all over

both sides rear inner sill/suspension mount areas have corrosion

Battery insecure and likely to fall from carrier (4.13 (a) (ii))

Nearside Headlamp has a product on the lens so that the light output is severely reduced glass dull and faded (4.1.4 (b))

Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i))

Nearside Rear Upper Coil spring fractured or broken (5.3.1 (b) (i))

Offside Front Position lamp not working (4.2.1 (a) (ii))

Offside Headlamp has a product on the lens so that the light output is severely reduced glass dull and faded (4.1.4 (b))

Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i))

Offside Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Rear Service brake excessively fluctuating both sides (1.2.1 (e))

Front front lower sub frame and lower arms have corrosion

Nearside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

UNDERSIDE, none specific corrosion all over

both sides rear inner sill/suspension mount areas have corrosion

Nearside Play in steering rack inner joint(s) ()

Nearside Rear Coil spring corroded (5.3.1 (b) (i))

Offside Front Suspension arm pin or bush worn but not resulting in excessive movement rear bush (5.3.4 (a) (i))

Offside Rear Direction indicator slightly discoloured (4.4.3 (a))

Offside Rear Wheel bearing slightly noisy (5.1.3 (b) (i))

Oil leak, but not excessive engine bay area (8.4.1 (a) (i))

body corrosion

fuel filler neck corroded

general corrosion

Front Anti-roll bar linkage pin or bush excessively worn both (5.3.4 (a) (i))

Nearside Front Wheel bearing rough when rotated (5.1.3 (b) (i))

Offside Front Headlamp has a product on the lens so that the light output is severely reduced misty (4.1.4 (b))

Offside Rear Coil spring fractured or broken (5.3.1 (b) (i))

Nearside Headlamp has a product on the lens but not seriously reducing light output (4.1.4 (b))

Nearside Play in steering rack inner joint(s) ()

Nearside Rear Coil spring corroded (5.3.1 (b) (i))

Offside Front Suspension arm pin or bush worn but not resulting in excessive movement rear bush (5.3.4 (a) (i))

Offside Rear Direction indicator slightly discoloured (4.4.3 (a))

Offside Rear Wheel bearing slightly noisy (5.1.3 (b) (i))

Oil leak, but not excessive engine bay area (8.4.1 (a) (i))

body corrosion

fuel filler neck corroded

general corrosion

Nearside Headlamp has a product on the lens but not seriously reducing light output (1.7.5a)

Offside Headlamp has a product on the lens but not seriously reducing light output (1.7.5a)

front exhaust sbracket becoming correded

Windscreen washer provides insufficient washer liquid (8.2.3)

Nearside Rear Shock absorber has a light misting of oil (2.7.3)

Exhaust emissions Lambda reading after 2nd fast idle outside specified limits (7.3.D.3)

Exhaust has a major leak of exhaust gases (7.1.2)

Nearside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Offside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Offside Rear Shock absorber has negligible damping effect (2.7.5)

Registration plate lamp not working (1.1.C.1d)

Nearside Rear Shock absorber has a light misting of oil (2.7.3)

Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.5b)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

ps drive belt cracking

Front Anti-roll bar rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)