MOT Status
ValidMileage
116,534 miSignificantly above average — investigate
Not all car check providers offer a guarantee. Don't risk buying from services that can't back their data. CarVerify reports include a £30,000 finance data guarantee.
Vehicle Details
All premium checks include
50+ data pointsMOT History
Offside Rear Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))
Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))
Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b))
Nearside Front Headlamp aim too low adjuster inoperative (4.1.2 (a))
Nearside Rear Registration plate lamp missing in the case of a single lamp or all lamps (4.7.1 (b) (ii))
Offside Front Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))
Offside Rear Parking brake efficiency below requirements (1.4.2 (a) (i))
Offside Rear Registration plate lamp missing in the case of a single lamp or all lamps (4.7.1 (b) (ii))
Nearside Front Suspension arm pin or bush worn but not resulting in excessive movement rear bush (5.3.4 (a) (i))
Nearside Rear Coil spring corroded (5.3.1 (b) (i))
Nearside Rear Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))
Nearside Rear Position lamp slightly affected by the operation of another lamp (4.2.3 (c))
Offside Front Headlamp aim too high (4.1.2 (a))
Offside Front Play in steering rack inner joint(s) inner arm ()
Offside Front Suspension arm pin or bush worn but not resulting in excessive movement rear bush (5.3.4 (a) (i))
Offside Front Tyre worn close to legal limit/worn on edge worn on edges (5.2.3 (e))
Offside Rear Coil spring corroded (5.3.1 (b) (i))
Offside Rear Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))
Offside Rear Position lamp slightly affected by the operation of another lamp (4.2.3 (c))
Oil leak, but not excessive (8.4.1 (a) (i))
front bumper damaged
Exhaust has a minor leak of exhaust gases (6.1.2 (a))
Nearside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement Inner front bush (5.3.4 (a) (i))
Nearside Rear Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))
Offside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement Inner front bush (5.3.4 (a) (i))
Offside Rear Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))
Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))
Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturer's specified limits (8.2.1.2 (a))
Hazard warning lamps inoperative (4.4.1 (e))
Offside Headlamp not working on dipped beam (4.1.1 (a) (ii))
Offside Stop lamp(s) not working (4.3.1 (a) (ii))
Parking brake efficiency below requirements (1.4.2 (a) (i))
Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))
Windscreen washer provides insufficient washer liquid (3.5 (a))
Exhaust has a minor leak of exhaust gases (6.1.2 (a))
Nearside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement Inner front bush (5.3.4 (a) (i))
Nearside Rear Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))
Offside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement Inner front bush (5.3.4 (a) (i))
Offside Rear Integral body structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))
Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))
Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))
Front Direction indicator slightly discoloured both (4.4.3 (a))
Nearside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))
Oil leak, but not excessive gearbox (8.4.1 (a) (i))
Rear Brake pad(s) wearing thin (1.1.13 (a) (ii))
Rear Direction indicator slightly discoloured both (4.4.3 (a))
Nearside Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Nearside Rear Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))
Nearside Rear Coil spring corroded (5.3.1 (b) (i))
Offside Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Offside Rear Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))
Offside Rear Coil spring corroded (5.3.1 (b) (i))
Rear Exhaust has a minor leak of exhaust gases (6.1.2 (a))
Rear Registration plate deteriorated but not likely to be misread (0.1 (b))
Windscreen damaged but not adversely affecting driver's view (3.2 (a) (i))
Nearside Front Brakes imbalanced across an axle (1.2.1 (b) (i))
Nearside Headlamp aim too low (4.1.2 (a))
Nearside Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Nearside Rear Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))
Nearside Rear Coil spring corroded (5.3.1 (b) (i))
Offside Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))
Offside Rear Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))
Offside Rear Coil spring corroded (5.3.1 (b) (i))
Rear Exhaust has a minor leak of exhaust gases (6.1.2 (a))
Rear Registration plate deteriorated but not likely to be misread (0.1 (b))
Windscreen damaged but not adversely affecting driver's view (3.2 (a) (i))
Offside Front Lower Suspension component ball joint excessively worn (5.3.4 (a) (i))
Rear Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))
Rear Brake pad(s) wearing thin (1.1.13 (a) (ii))
Front Brake pipe corroded, covered in grease or other material bothsides (1.1.11 (c))
Nearside Rear Exhaust has a minor leak of exhaust gases joint (6.1.2 (a))
Nearside Rear Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))
Rear Brake hose has slight corrosion to ferrule bothsides (1.1.12 (f) (i))
Rear Suspension arm pin or bush worn but not resulting in excessive movement bothsides (5.3.4 (a) (i))
Front Brake hose has slight corrosion to ferrule bothsides (1.1.12 (f) (i))
Offside Front Oil leak, but not excessive (8.4.1 (a) (i))
Rear Inner Suspension component mounting prescribed area is corroded but not considered excessive sills (5.3.6 (a) (i))
Rear Suspension arm pin or bush worn but not resulting in excessive movement bothsides (5.3.4 (a) (i))
Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))
Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))
Parking brake efficiency below requirements (1.4.2 (a) (i))
Front Brake hose has slight corrosion to ferrule bothsides (1.1.12 (f) (i))
Offside Front Oil leak, but not excessive (8.4.1 (a) (i))
Rear Inner Suspension component mounting prescribed area is corroded but not considered excessive sills (5.3.6 (a) (i))
Rear Suspension arm pin or bush worn but not resulting in excessive movement bothsides (5.3.4 (a) (i))
Offside Rear Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))
Nearside Front Nail in tyre ()
Park brake efficiency only just met requirements
Rear numberplate characters faded
Offside Stop lamp(s) not working (4.3.1 (a) (ii))
Oil leaking excessively from engine (8.4.1 (a) (i))
Nearside Front Nail in tyre ()
Park brake efficiency only just met requirements
Rear numberplate characters faded
Nearside Front Outer Tyre has a cut but not deep enough to reach the ply or cords wall (5.2.3 (d) (i))
Windscreen wiper blade defective (3.4 (b) (i))
Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))
Exhaust has a major leak of exhaust gases (6.1.2 (a))
Nearside Front Position lamp not working (4.2.1 (a))
Nearside Headlamp aim too high (4.1.2 (a))
Nearside Headlamp insecure (4.1.1 (c))
Nearside Stop lamp(s) not working (4.3.1 (a) (ii))
Offside Rear Parking brake inoperative on one side (1.4.1 (a))
Parking brake efficiency below requirements (1.4.2 (a) (i))
Windscreen wiper blade defective (3.4 (b) (i))
Nearside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement rear bush (2.4.G.2)
Nearside Rear coil spring corroded (2.4.C.1b)
Offside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement rear bush (2.4.G.2)
Offside Rear coil spring corroded (2.4.C.1b)
Offside Front Brake pad(s) less than 1.5 mm thick (3.5.1g)
Offside Front Front position lamp(s) not working (1.1.A.3b)
Offside Obligatory mirror seriously damaged, affecting the rear view (8.1.2a)
Front brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)
Nearside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement rear bush (2.4.G.2)
Nearside Rear coil spring corroded (2.4.C.1b)
Offside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement rear bush (2.4.G.2)
Offside Rear coil spring corroded (2.4.C.1b)
Nearside Front Anti-roll bar linkage ball joint dust cover deteriorated, but preventing the ingress of dirt (2.4.G.2)
Nearside Front Lower Suspension arm rubber bush deteriorated but not resulting in excessive movement rear bush (2.4.G.2)
Offside Front Anti-roll bar linkage ball joint dust cover deteriorated, but preventing the ingress of dirt (2.4.G.2)
Offside Front Lower Suspension arm rubber bush deteriorated but not resulting in excessive movement rear bush (2.4.G.2)
Nearside Front Headlamp insecure (1.7.3)
Nearside Rear Seat belt locking mechanism does not secure or release (5.2.5a)
Offside Rear Seat belt locking mechanism does not secure or release (5.2.5a)
Offside rear parking brake recording little or no effort (3.7.B.6a)
Parking brake: efficiency below requirements (3.7.B.7)
Nearside Front Anti-roll bar linkage ball joint dust cover deteriorated, but preventing the ingress of dirt (2.4.G.2)
Nearside Front Lower Suspension arm rubber bush deteriorated but not resulting in excessive movement rear bush (2.4.G.2)
Offside Front Anti-roll bar linkage ball joint dust cover deteriorated, but preventing the ingress of dirt (2.4.G.2)
Offside Front Lower Suspension arm rubber bush deteriorated but not resulting in excessive movement rear bush (2.4.G.2)
Nearside Front Anti-roll bar linkage ball joint dust cover damaged, but preventing the ingress of dirt (2.4.G.2)
Nearside Front Lower Suspension arm has slight play in a pin/bush rear bush (2.4.G.2)
exhaust flexi bracket broken
Offside Front Anti-roll bar linkage has excessive play in a ball joint (2.4.G.2)
Nearside Front Anti-roll bar linkage ball joint dust cover damaged, but preventing the ingress of dirt (2.4.G.2)
Nearside Front Lower Suspension arm has slight play in a pin/bush rear bush (2.4.G.2)
exhaust flexi bracket broken
Nearside Windscreen wiper does not clear the windscreen effectively (8.2.2)
Offside Windscreen wiper does not clear the windscreen effectively (8.2.2)
Offside Front Anti-roll bar linkage has slight play in a ball joint (2.4.G.2)
Windscreen washer provides insufficient washer liquid (8.2.3)
Engine covers fitted obscuring some components in the engine bay
Under-trays fitted obscuring some underside components
Front exhaust bracket broken
Rear exhaust box corroded
Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.5b)
Nearside Rear Brake hose has slight corrosion to ferrules (3.6.B.4e)
Offside Rear Brake hose has slight corrosion to ferrules (3.6.B.4e)
Rear Exhaust has part of the system slightly deteriorated (7.1.1a)
Nearside Rear Tyre has a tear, caused by separation or partial failure of its structure (4.1.D.1b) DANGEROUS
How Reliable is the Fiat Punto?
Based on 6,712,102 MOT tests across 579,551 vehicles.
Top MOT Failure Points
Don't risk it. Know before you buy.
Not all vehicle check providers are the same. Some don't offer a data guarantee, which means if their information is wrong, you're on your own. Every CarVerify report is backed by a £30,000 finance data guarantee.
Y24 WAK is a 2012 Fiat Punto in Black with a 1,248cc petrol engine. This vehicle has been through 39 MOT tests with a personal pass rate of 66.7%.
Across all 2012 Fiat Punto models, the average MOT pass rate is 72.5% with a typical mileage of 51,720 miles. This particular vehicle has a lower pass rate than the average for its year, which may indicate maintenance issues worth investigating.
The most common reason a Fiat Punto fails its MOT is tyre tread depth below requirements of 1.6mm, accounting for 377,326 recorded failures. If you're considering buying Y24 WAK, it's worth having these areas checked by a mechanic before committing.
The Fiat Punto typically stays on UK roads for around 32 years. At 14 years old, this Fiat Punto is still in the earlier part of its expected life.
Frequently Asked Questions
How do I check the history of Y24 WAK?
You can check the full history of Y24 WAK by running a full vehicle check. This shows you finance, stolen, write-off, MOT history, mileage records and more.
What year was Y24 WAK registered?
Y24 WAK is a 2012 Fiat Punto, first registered on 27 March 2012.
Is Y24 WAK safe to buy?
The MOT history for Y24 WAK shows 39 tests with a 66.7% pass rate. To check for outstanding finance, stolen markers, write-off history and mileage discrepancies, run a full vehicle check.
Does Y24 WAK have outstanding finance?
Finance checks require a premium vehicle report. This checks against all major UK finance providers to see if there is any outstanding finance on Y24 WAK. If you buy a car with outstanding finance, the finance company can repossess it.
No warranty or guarantee of accuracy is provided for any free data on this page. The data guarantee applies only to information obtained through the purchase of a full check.