2001 Renault Master

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Nearside Cab or chassis corroded within 30cm of a mounting, but not seriously affecting overall security inner and outer sill (6.2.2 (d) (i))

Nearside Front Upper Suspension arm ball joint has slight play (5.3.4 (a) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Nearside Front Inner Drive shaft joint constant velocity boot severely deteriorated (6.1.7 (g) (i))

Offside Rear inner arch to floor

Oil leak, but not excessive (8.4.1 (a) (i))

under body in poor condition at rear end

Exhaust emissions exceed manufacturer's specified limit (8.2.2.2 (a))

Nearside Outer Body panel corroded and likely to cause injury sill (6.2.1 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i))

Offside Front Bumper insecure (6.1.4 (a) (i))

Offside Parking brake inoperative on one side (1.4.1 (a))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis in several places (5.3.6 (a) (i))

Service brake efficiency below requirements (1.2.2 (a) (i))

Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) DANGEROUS

1.55 plate limit

Brake load sensing valve stiff (1.1.17 (c) (ii))

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Front Inner Drive shaft joint constant velocity boot severely deteriorated (6.1.7 (g) (i))

Offside Front Upper Suspension arm ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Offside Rear Inner Integral body structure is corroded but structural rigidity is not significantly reduced wheel arch area corroded an holed outside prescribed area (6.1.1 (c) (i))

Oil leak, but not excessive (8.4.1 (a) (i))

Supplementary restraint system warning lamp does not illuminate (7.1.6 (a))

Nearside Front Upper Suspension arm ball joint has slight play (5.3.4 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis next to rear outrigger (5.3.6 (a) (i))

Offside Front Lower Shock absorbers has an excessively worn bush (5.3.2 (c))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer and inner sill next to front leaf spring mount (5.3.6 (a) (i))

Nearside Front Upper Suspension arm ball joint has slight play (5.3.4 (a) (i))

Nearside Front Suspension component ball joint has slight play (5.3.4 (a) (i))

Offside Rear Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Nearside Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Nearside Front Brake hose has slight corrosion to ferrule x2 (1.1.12 (f) (i))

Nearside Front Brake pipe corroded, covered in grease or other material at caliper x2 (1.1.11 (c))

Offside Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Offside Front Brake hose has slight corrosion to ferrule x1 (1.1.12 (f) (i))

Offside Front Brake pipe corroded, covered in grease or other material at caliper (1.1.11 (c))

Offside Rear Suspension component mounting repair covered in underseal inner arch and spring mounting (5.3.6 (a) (i))

Offside Rear Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Power steering pipe/hose slightly corroded front (2.1.5 (g) (i))

Suspension component mounting prescribed area is corroded but not considered excessive all rear at chassis and inner arches (5.3.6 (a) (i))

Suspension component mounting prescribed area is corroded but not considered excessive n/s and o/s outer sills (5.3.6 (a) (i))

brake fluid contamination to all inner tyre walls no signs of leaks

o/s front brake hoses secured by cable ties

o/s front top ball joint not fully seated in arm

Battery insecure and likely to fall from carrier (4.13 (a) (ii))

Brake performance not tested burst pipes (1.2.1 (g))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength spring hanger (5.3.6 (a) (i))

Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Offside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength box section (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i))

Offside Front Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) DANGEROUS

Nearside Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Nearside Front Brake pipe corroded, covered in grease or other material x 4 brake pipes (1.1.11 (c))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive chassis (5.3.6 (a) (i))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive inner wheel arch (5.3.6 (a) (i))

Offside Driver's door catch deteriorated so the door cannot be readily opened or closed (6.2.3 (c) (i))

Offside Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Offside Front Brake pipe corroded, covered in grease or other material x 4 brake pipes (1.1.11 (c))

Offside Front brake hoses insecure

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive chassis (5.3.6 (a) (i))

Offside Rear Tyre slightly damaged/cracking or perishing (5.2.3 (d) (ii))

Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Front Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Front Subframe mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Nearside Front Service brake binding but not excessively (1.2.1 (f))

Nearside Rear Brake load sensing valve stiff (1.1.17 (c) (ii))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive spring mounting bracket (5.3.6 (a) (i))

Offside Front Upper Suspension arm ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive spring mounting bracket (5.3.6 (a) (i))

Rear Parking brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (1.4.2 (a) (i))

Front Registration plate inscription illegible (0.1 (b))

Front Windscreen wiper does not clear the windscreen effectively both sides (3.4 (b) (ii))

Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting under passengers door sill to jacking point (6.2.2 (d) (i))

Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting under drivers door sill to jacking point (6.2.2 (d) (i))

Offside Front Service brake excessively binding (1.2.1 (f))

Rear Registration plate inscription illegible (0.1 (b))

Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Front Brake hose has slight corrosion to ferrule (1.1.12 (f) (i))

Front Subframe mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Nearside Front Service brake binding but not excessively (1.2.1 (f))

Nearside Rear Brake load sensing valve stiff (1.1.17 (c) (ii))

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive spring mounting bracket (5.3.6 (a) (i))

Offside Front Upper Suspension arm ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive spring mounting bracket (5.3.6 (a) (i))

Rear Parking brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (1.4.2 (a) (i))

Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength jacking point (5.3.6 (a) (i))

Nearside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))

Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength jacking point (5.3.6 (a) (i))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))

Service brake efficiency below requirements (1.2.2 (a) (i))

Windscreen washer provides insufficient washer liquid (3.5 (a))

Front Registration plate deteriorated but not likely to be misread (0.1 (b))

Offside Front Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Front Service brake binding but not excessively (1.2.1 (f))

Offside Rear Outer Integral body structure is corroded but structural rigidity is not significantly reduced sill (6.1.1 (c) (i))

Front registration plate deteriorated but not likely to be misread (6.3.1d)

Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive inner sill (2.4.A.3)

Offside Front Brake pipe slightly corroded (3.6.B.2c)

Offside Front Lower Shock absorber has a slightly worn bush (2.7.4)

Offside Front constant velocity joint gaiter deteriorated, but preventing the ingress of dirt (2.5.C.1a)

Battery insecure (1.9.1)

Brake load sensing valve linkage defective and function impaired rod snapped (3.6.E.3)

Nearside Front Tyre has a tear, caused by separation or partial failure of its structure (4.1.D.1b)

Nearside Rear Tyre has a tear, caused by separation or partial failure of its structure (4.1.D.1b)

Nearside front brake binding (3.7.B.1)

Offside Rear Body has a sharp edge caused by damage (6.1.C.1)

Offside front brake binding (3.7.B.1)

Parking brake: efficiency below requirements (3.7.B.7)

Windscreen washer provides insufficient washer liquid (8.2.3)

Front registration plate deteriorated but not likely to be misread (6.3.1d)

Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive inner sill (2.4.A.3)

Offside Front Brake pipe slightly corroded (3.6.B.2c)

Offside Front Lower Shock absorber has a slightly worn bush (2.7.4)

Offside Front constant velocity joint gaiter deteriorated, but preventing the ingress of dirt (2.5.C.1a)

Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive inner sill (2.4.A.3)

Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive shackle mount (2.4.A.3)

Offside Front Front constant velocity joint gaiter deteriorated, but preventing the ingress of dirt (2.5.C.1a)

Offside Front Lower Shock absorber has a slightly worn bush (2.7.4)

Offside Rear Suspension spring mounting prescribed area is corroded but not considered excessive shackle mount (2.4.A.3)

Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive inner sill (2.4.A.3)

Nearside Rear Suspension spring mounting prescribed area is corroded but not considered excessive shackle mount (2.4.A.3)

Offside Front Front constant velocity joint gaiter deteriorated, but preventing the ingress of dirt (2.5.C.1a)

Offside Front Lower Shock absorber has a slightly worn bush (2.7.4)

Offside Rear Suspension spring mounting prescribed area is corroded but not considered excessive shackle mount (2.4.A.3)

Windscreen washer provides insufficient washer liquid (8.2.3)

Front Windscreen washer provides insufficient washer liquid (8.2.3)

Nearside Front Headlamp aim too high (1.8)

Nearside Rear Anti-roll bar linkage synthetic bush deteriorated resulting in excessive movement detatched (2.4.G.2)

Offside Front Headlamp aim too high (1.8)

Offside Rear Brake pipe excessively corroded to flexy hose (3.6.B.2c)

Parking brake: efficiency below requirements (3.7.B.7)

Service brake: efficiency below requirements (3.7.B.7)

Nearside Rear Brake pad(s) less than 1.5 mm thick (3.5.1g)

Nearside Windscreen wiper does not clear the windscreen effectively (8.2.2)

Parking brake: efficiency below requirements (3.7.B.7)

n/s/r brake disc scored/worn

o/s wiper worn

rear exhaust support bracket rubber perished/split

Offside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a)

Parking brake: efficiency below requirements (3.7.B.7)

Service brake: efficiency below requirements (3.7.B.7)

Nearside Front Brake pipe slightly corroded (3.6.B.2c)

Nearside Parking brake: parking brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.7)

Offside Front Brake pipe slightly corroded (3.6.B.2c)

Offside Outer Front constant velocity joint gaiter deteriorated (2.5.C.1a)

Offside Parking brake: parking brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.7)

Offside Rear Brake pipe slightly corroded (3.6.B.2c)

Nearside Outer Front Lower Suspension arm has slight play in a ball joint (2.4.G.2)

Nearside Parking brake: parking brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.7)

Offside Parking brake: parking brake efficiency only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.7)

Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. (3.7.B.5b)

Nearside Front Lower Suspension arm has slight play in a ball joint (2.4.G.2)

Brake cable has restricted free movement (3.5.1k)

Fuel system component leaking (7.2.3)

Nearside brake disc excessively pitted (3.5.1h)

Offside Rear brake disc excessively pitted (3.5.1h)

Brakes imbalanced across an axle (3.7.B.5b) DANGEROUS

Parking brake: efficiency below requirements (3.7.B.7) DANGEROUS

Service brake: efficiency below requirements (3.7.B.7) DANGEROUS