2001 Fiat Scudo

Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength out rigger (5.3.6 (a) (i))

Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength out rigger (5.3.6 (a) (i))

Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))

Service brake efficiency below requirements (1.2.2 (a) (i))

Front Brakes imbalanced across an axle by more than 50% Axle 1 (1.2.1 (b) (ii)) DANGEROUS

Nearside Front Direction indicator not working (4.4.1 (a) (ii))

Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jacking piont (5.3.6 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member (5.3.6 (a) (i))

Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jacking piont (5.3.6 (a) (i))

Offside Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength out rigger (5.3.6 (a) (i))

corrosion under vehicle

Nearside Front constant velocity joint gaiter deteriorated, but preventing the ingress of dirt (2.5.C.1a)

Nearside Front wheel bearing has slight play (2.5.A.3c)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Front constant velocity joint gaiter deteriorated, but preventing the ingress of dirt (2.5.C.1a)

Nearside Rear Road wheel with a slightly distorted bead rim (4.2.A.1a)

wheel bearing type noise when driven. unable to locate during mot test.

Nearside Rear Suspension component mounting prescribed area is excessively corroded sill & rear of sill (2.4.A.3)

Offside Rear Suspension component mounting prescribed area is excessively corroded sill & rear of sill (2.4.A.3)

Nearside Rear Road wheel with a slightly distorted bead rim (4.2.A.1a)

Offside Headlamp aim too low (1.8)

wheel bearing type noise when driven. unable to locate during mot test.

advise oil leak.

Nearside Front constant velocity joint is insecure (2.5.C.1b)

Nearside Front Tyre worn close to the legal limit AT LIMIT! (4.1.E.1)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Windscreen has damage to the swept area in excess of a 40mm circle outside zone 'A' (8.3.1d)

advise oil leak.

Battery insecure (1.9.1)

Nail in nearside rear tyre

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Registration plate lamp not working (1.1.C.1d)

Front number plate damaged

Nearside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Offside Front Suspension arm rubber bush deteriorated but not resulting in excessive movement (2.4.G.2)

Nearside Front Brake pad(s) wearing thin (3.5.1g)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Front Brake pad(s) wearing thin (3.5.1g)

front no. plate starting to crack

Nearside Rear Rear fog lamp not working (1.3.2b)

Nearside Rear Registration plate lamp not working (1.1.C.1d)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)