2003 Audi A2

Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h))

Exhaust has a major leak of exhaust gases cat (6.1.2 (a))

Offside Front Shock absorbers has a serious fluid leak (5.3.2 (b))

Nearside Front Anti-roll bar linkage insecure and impairing directional stability (5.3.3 (a) (ii)) DANGEROUS

Nearside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h))

Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii))

Nearside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Nearside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Offside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Offside Rear Brake pipe corroded, covered in grease or other material to flexy (1.1.11 (c))

Rear Passenger seat(s) missing at time of test ()

Rear Sound deadening material not fully secure (8.1.1 (b) (i))

under-trays fitted obscuring some underside components

Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h))

Nearside Front Macpherson strut top bush or bearing has excessive wear or free play (5.3.4 (a) (i))

Offside Rear Brake disc significantly and obviously worn (1.1.14 (a) (i))

Offside Rear Service brake excessively binding (1.2.1 (f))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Rear Brakes imbalanced across an axle Axle 2 (1.2.1 (b) (i))

Nearside Front Tyre tread depth below requirements of 1.6mm (5.2.3 (e)) DANGEROUS

Nearside Rear Brake pad(s) less than 1.5 mm thick (1.1.13 (a) (ii)) DANGEROUS

Offside Front Tyre tread depth below requirements of 1.6mm (5.2.3 (e)) DANGEROUS

Front Undertray not fully secure (8.1.1 (b) (i))

Nearside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Nearside Rear Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Nearside Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Nearside Rear Service brake binding but not excessively (1.2.1 (f))

Offside Front Anti-roll bar linkage ball joint has slight play (5.3.4 (a) (i))

Offside Rear Brake pipe corroded, covered in grease or other material to flexy (1.1.11 (c))

Rear Passenger seat(s) missing at time of test ()

Rear Sound deadening material not fully secure (8.1.1 (b) (i))

under-trays fitted obscuring some underside components

Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h))

Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))

Nearside Rear Service brake binding but not excessively (1.2.1 (f))

Nearside Rear Brake pipe excessively corroded (3.6.B.2c)

Offside rear brake binding (3.7.B.1)

rear brake application uneven (3.7.B.2)

Exhaust emissions Lambda reading after 2nd fast idle outside specified limits (7.3.D.3)

EML LIGHT ON

Nearside Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Offside Rear brake disc worn, pitted or scored, but not seriously weakened (3.5.1i)

Offside Rear Shock absorber has a light misting of oil (2.7.3)

eml on

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Front Exhaust has a minor leak of exhaust gases (7.1.2)

Offside Stop lamp not working (1.2.1b)

Front Exhaust has a minor leak of exhaust gases (7.1.2)

Registration plate lamp not working (1.1.C.1d)

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Brake pad(s) less than 1.5 mm thick (3.5.1g)

Offside Rear rear brake binding (3.7.B.1)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)