2008 Toyota Aygo

Nearside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting SILL (6.2.2 (d) (i))

Offside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting SILL (6.2.2 (d) (i))

Offside Rear Parking brake inoperative on one side (1.4.1 (a))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Nearside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Front Drive shaft joint constant velocity boot severely deteriorated (6.1.7 (g) (i))

Rear Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

parking brake reserve travel just met

Nearside Front Suspension component ball joint excessively worn (5.3.4 (a) (i))

Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii))

Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sills (7.1.1 (a) (i))

Nearside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Front Drive shaft joint constant velocity boot severely deteriorated (6.1.7 (g) (i))

Rear Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

parking brake reserve travel just met

Nearside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Rear Coil spring corroded x2 (5.3.1 (b) (i))

both axle mounts corroded

sills corroded x2

subframe corroded

underbody corroded

vehicle heavily undersealed

Exhaust has a major leak of exhaust gases (6.1.2 (a))

Nearside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))

Offside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Nearside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Anti-roll bar pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Rear Brake pipe corroded, covered in grease or other material (1.1.11 (c))

Rear Coil spring corroded x2 (5.3.1 (b) (i))

both axle mounts corroded

sills corroded x2

subframe corroded

underbody corroded

vehicle heavily undersealed

Nearside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i))

Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i))

Offside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Nearside Rear Tyre tread depth below requirements of 1.6mm (5.2.3 (e)) DANGEROUS

Front Sub-frame corroded but not seriously weakened (5.3.3 (b) (i))

Offside Front Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Outer Seat belt anchorage prescribed area is corroded but not considered excessive sill (7.1.1 (a) (i))

Rear Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Rear Inner Seat belt anchorage prescribed area is corroded but not considered excessive both sides sills (7.1.1 (a) (i))

Rear Suspension component mounting prescribed area is corroded but not considered excessive both sides (5.3.6 (a) (i))

Rear Suspension component mounting prescribed area is corroded but not considered excessive both sides (5.3.6 (a) (i))

Rear Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Nearside Front Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Position lamp not working (4.2.1 (a) (ii))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Nearside Front Tyre tread depth below requirements of 1.6mm (5.2.3 (e)) DANGEROUS

Offside Front Tyre has ply or cords exposed (5.2.3 (d) (ii)) DANGEROUS

Nearside Front Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Front Suspension arm pin or bush worn but not resulting in excessive movement Nearside and Offside (5.3.4 (a) (i))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Front Suspension arm pin or bush worn but not resulting in excessive movement Nearside and Offside (5.3.4 (a) (i))

Nearside Front Position lamp not working (4.2.1 (a) (ii))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Front Windscreen wiper blade defective (3.4 (b) (i))

Both front brake discs are pitted on their inner faces

Offside rear tyre is worn on both edges.

Front brake discs are becoming pitted on their inner faces

Front tyres are wearing on both edges

Offside rear tyre is becoming perished and cracked

Front Windscreen wiper does not clear the windscreen effectively (8.2.2)

offside rear tyre is becoming perished

offside rear tyre is becoming perished

Offside Headlamp not working on dipped beam (1.7.5a)