2010 Aprilia SX 50 MY06

Front Brake disc contaminated (1.1.14 (b))

Headlamp aim too low (4.1.2 (a))

Nearside Front Shock absorber has a serious fluid leak (5.3.2 (b))

Offside Front Shock absorber has a serious fluid leak (5.3.2 (b))

Rear Brake excessively binding (1.2.1 (f))

Rear reflector missing (4.8.2 (a) (ii))

Suspension arm pin or bush excessively worn (5.3.4 (a) (i))

Front Brake binding but not excessively (1.2.1 (f))

no mirrors fitted

Exhaust has a major leak of exhaust gases (6.1.2 (a))

Front Wheel has a slightly distorted bead rim (5.2.2 (c) (i))

Horn not working (7.7 (a) (ii))

Registration plate does not conform to the specified requirements (0.1 (d))

Front Wheel has a slightly distorted bead rim (5.2.2 (c) (i))

Front Front shock absorber has light misting of stanchion (2.3.3)

Rear Rear wheel bearings have slight free play (2.4.A.2c)

Wheel alignment slightly misaligned. (2.5.1)

Front Front shock absorber has light misting of stanchion (2.3.3)

Front Front suspension assembly slightly bent (2.3.1)

Rear Brake pad(s) close to minimum limit (3.2.A1f(i))

Rear Drive chain excessively tight (6.2.1d)

Front Front shock absorber has light misting of stanchion (2.3.3)

Front Front suspension assembly slightly bent (2.3.1)

Rear Brake pad(s) close to minimum limit (3.2.A1f(i))

Front Headlamp at least one does not illuminate on dipped beam (1.2.2a(i))

Front Wheel alignment incorrect which adversely affects the steering (2.5.1)

Rear Built up wheel has a loose bolt/s (4.2.1c)

Rear Exhaust excessively deteriorated (7.1.1a)

Rear Exhaust noise is clearly in excess of that emitted by a similar motor bicycle fitted with a standard silencer in average condition (7.1.2)

Front Front shock absorber has light misting of stanchion (2.3.3)

Rear Brake pad(s) close to minimum limit (3.2.A1f(i))

Rear Drive chain slightly loose (6.2.1d)

Decelerometer brake test no brake control achieves an efficiency of 30% (3.3.E1a)

Front All position lamps do not illuminate immediately when switched on (1.1.3a)

Rear Brake pad(s) less than 1.5 mm thick (3.2.A1f(i))

Rear Rear wheel spindle loose (2.4.A.2b)

Rear Registration plate with character(s) which are not of equal width along their entire length (6.3.4a)

Front Tyre worn close to the legal limit (4.1.3(ii))

Offside Front shock absorber has light misting of stanchion (2.3.3)

Rear Tyre worn close to the legal limit (4.1.3(ii))

Drive chain excessively loose (6.2.1d)

Horn is not a constant note (1.7.3c)

Rear Brake disc(s) cracked (3.2.A1g)

Rear Brake pad(s) less than 1.5 mm thick (3.2.A1f(i))

Front Tyre worn close to the legal limit (4.1.3(ii))

Offside Front shock absorber has light misting of stanchion (2.3.3)

Rear Tyre worn close to the legal limit (4.1.3(ii))

Drive chain slightly loose (6.2.1d)

Rear Roller brake test indicates slight fluctuation of brake effort (3.3.A1d)

Wheel alignment slightly misaligned. (2.5.1)

Headlamp at least one does not illuminate on dipped beam (1.2.2a(i))

Rear reflector on motorcycle missing (1.4.1)

Drive chain slightly loose (6.2.1d)

Rear Roller brake test indicates slight fluctuation of brake effort (3.3.A1d)

Wheel alignment slightly misaligned. (2.5.1)

Front Brake pad(s) close to minimum limit (3.2.A1f(i))

Rear Brake pad(s) less than 1.5 mm thick (3.2.A1f(i))

Front Brake pad(s) close to minimum limit (3.2.A1f(i))

Drive chain excessively tight (6.2.1d)

Locking device(s) not correctly fitted which may make the motor bicycle dangerous to ride (6.2.1h)