2017 Peugeot 208

Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h))

exhaust flexie sealed in putty

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive chassis leg (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive chassis leg (5.3.6 (a) (i))

exhaust flexi section worn and leaking, benefit of the doubt has been given as not considered to be excessive, system secure and passing emissions test

rear axle suffering from corrosion but not excessive

Bonnet cannot be secured in the closed position (3.1 (b) (i))

Bonnet primary retaining device ineffective (3.1 (c))

Nearside Front Service brake excessively fluctuating (1.2.1 (e))

Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii))

Nearside Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Offside Front Service brake excessively fluctuating (1.2.1 (e))

Offside Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Bonnet seriously at risk of opening inadvertently (3.1 (b) (ii)) DANGEROUS

Nearside Front Brake disc in such a condition that it is seriously weakened (1.1.14 (a) (ii)) DANGEROUS

Nearside Front Inner Brake pad(s) less than 1.5 mm thick (1.1.13 (a) (ii)) DANGEROUS

Offside Front Brake disc in such a condition that it is seriously weakened (1.1.14 (a) (ii)) DANGEROUS

Offside Front Inner Brake pad(s) less than 1.5 mm thick (1.1.13 (a) (ii)) DANGEROUS

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive chassis leg (5.3.6 (a) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive chassis leg (5.3.6 (a) (i))

exhaust flexi section worn and leaking, benefit of the doubt has been given as not considered to be excessive, system secure and passing emissions test

low oil pressure light came on at end of emissions test, ordinarily this would be a reason for abandoning the test but as the test was complete benefit of the doubt has been given but issue should be immediately addressed

rear axle suffering from corrosion but not excessive

Front Brake disc worn, but not excessively (1.1.14 (a) (i))

Nearside Front Suspension arm ball joint has slight play (5.3.4 (a) (i))

Nearside Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Front Headlamp aim too low (4.1.2 (a))

Front Brake disc worn, but not excessively (1.1.14 (a) (i))

Nearside Front Suspension arm ball joint has slight play (5.3.4 (a) (i))

Nearside Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b))

Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i))

Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b))

Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i))

Offside Headlamp not working on dipped beam (4.1.1 (a) (ii))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Front Brakes imbalanced across an axle (1.2.1 (b) (i))

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Front Brake pad(s) less than 1.5 mm thick (1.1.13 (a) (ii)) DANGEROUS

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Front Exhaust mounting defective (6.1.2 (a))