2008 Mazda 6

Anti-lock braking system warning lamp indicates an ABS fault (1.6 (b))

Offside Front Position lamp incorrect colour (4.2.3 (a) (i))

Brake lever has insufficient reserve travel (1.1.2 (a))

Front Windscreen washer provides insufficient washer liquid (3.5 (a))

Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Nearside Front Upper Suspension arm pin or bush excessively worn inner bushing (5.3.4 (a) (i))

Nearside Rear Service brake excessively binding (1.2.1 (f))

Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Offside Front Upper Suspension arm pin or bush excessively worn inner bushing (5.3.4 (a) (i))

Offside Front Wheel bearing rough when rotated (5.1.3 (b) (i))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Rear Brake disc significantly and obviously worn over heated (1.1.14 (a) (i))

Rear Brake pad(s) less than 1.5 mm thick (1.1.13 (a) (ii)) DANGEROUS

Front Brake pad(s) wearing thin (1.1.13 (a) (ii))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

general suspension corrosion

rear centre exhaust pipe joint heavily corroded

Engine cover, undertrays and sill covers fitted obscuring some components

Exhaust system corroded

Rear Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. 35% imbalance (1.2.1 (b) (i))

Rear Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Rear bumper damaged

Rear suspension components corroded

Nearside Front Position lamp not working (4.2.1 (a) (ii))

Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))

Parking brake efficiency below requirements (1.4.2 (a) (i))

Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Engine cover, undertrays and sill covers fitted obscuring some components

Exhaust system corroded

Rear Brakes imbalanced requirements only just met. It would appear that the braking system requires adjustment or repair. 35% imbalance (1.2.1 (b) (i))

Rear Vehicle structure is corroded but structural rigidity is not significantly reduced (6.1.1 (c) (i))

Rear bumper damaged

Rear suspension components corroded

Exhaust emissions exceed default limit of 1.5m-1 (8.2.2.2 (b))

Nearside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Rear Brake pad(s) wearing thin (3.5.1g)

Tyre worn close to the legal limit both front (4.1.E.1)

rear brake discs corroded

rear suspension slightly coorroded

Nearside Front Anti-roll bar ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Nearside Front Inner Anti-roll bar has slight play in a pin/bush (2.4.G.2)

Nearside Front Tyre worn close to the legal limit (4.1.E.1)

Offside Front Inner Anti-roll bar has slight play in a pin/bush (2.4.G.2)

Offside Front Tyre worn close to the legal limit (4.1.E.1)

Nearside Front Brake pad(s) wearing thin (3.5.1g)

Nearside Rear Brake pad(s) wearing thin (3.5.1g)

Offside Front Brake pad(s) wearing thin (3.5.1g)

Offside Rear Brake pad(s) wearing thin (3.5.1g)

Nearside Front Brake pad(s) wearing thin (3.5.1g)

Offside Front Brake pad(s) wearing thin (3.5.1g)