2008 Toyota Aygo

Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Nearside Front Suspension arm ball joint has slight play (5.3.4 (a) (i))

Nearside Front Suspension arm pin or bush worn but not resulting in excessive movement Rear bush (5.3.4 (a) (i))

Nearside Front Track rod end ball joint has slight play (2.1.3 (b) (i))

Rear Service brake binding but not excessively (1.2.1 (f))

general underbody corrosion

Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))

Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b))

Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i))

Nearside Parking brake inoperative on one side (1.4.1 (a))

Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))

Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sills (6.1.1 (c) (i))

Offside Rear Service brake excessively binding (1.2.1 (f))

Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting within 30cm of sub frame mount (6.2.2 (d) (i))

Parking brake efficiency below requirements (1.4.2 (a) (i))

All coil springs corroded

Exhaust emissions - engine idle speed too low

Nearside Front Outer Drive shaft joint constant velocity boot severely deteriorated (6.1.7 (g) (i))

Nearside Rear Child Seat fitted not allowing full inspection of adult belt

Front Subframe mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Nearside Front Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength in front of rear arm marked in yellow (5.3.6 (a) (i))

Offside Headlamp not working on dipped beam (4.1.1 (a) (ii))

Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner floor sill to outer sill (7.1.1 (a) (i))

Front Subframe mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Front Windscreen wiper blade defective judders (3.4 (b) (i))

Nearside Front Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Anti-roll bar linkage pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Rear Service brake excessively binding (1.2.1 (f))

Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c))

Suspension component mounting prescribed area excessively corroded significantly reducing structural strength both outer sills (5.3.6 (a) (i))

Nearside rear parking brake recording little or no effort (3.7.B.6a)

Offside Rear Brake pipe kinked (3.6.B.2b)

Parking brake: efficiency below requirements (3.7.B.7)

rear parking (secondary) brakes imbalanced (3.7.B.6b)

Offside Headlamp aim beam image obviously incorrect (1.8.A.1b)

Offside Registration plate lamp not working (1.1.C.1d)

Offside Rear Suspension arm rubber mounting deteriorated resulting in excessive movement (2.4.G.2)

Nearside Front Headlamp aim too low (1.8)

Offside Front Headlamp aim too low (1.8)

Front Windscreen wiper does not clear the windscreen effectively (8.2.2)

Nearside Rear Registration plate lamp not working (1.1.C.1d)

Offside Rear Registration plate lamp not working (1.1.C.1d)

no coolant in header tank.

no coolant in header tank.

Nearside Headlamp aim too high (1.8)

Offside Headlamp aim too high (1.8)