2004 Fiat Panda

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Nearside Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

both chassis legs corroded , not holed

both side sills corroded , not holed

Nearside Front Headlamp aim too high and too far to the left. (4.1.2 (a))

Offside Rear Rear fog lamp not working (4.5.1 (a) (ii))

Front Brake disc worn, pitted or scored, but not seriously weakened (1.1.14 (a) (ii))

Nearside Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Offside Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

both chassis legs corroded , not holed

both side sills corroded , not holed

Central Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Nearside Front Coil spring corroded (5.3.1 (b) (i))

Offside Front Coil spring corroded (5.3.1 (b) (i))

Offside Rear Coil spring corroded (5.3.1 (b) (i))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Front Suspension arm pin or bush worn but not resulting in excessive movement rear bush (5.3.4 (a) (i))

Offside Rear Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Nearside Front Suspension arm pin or bush worn but not resulting in excessive movement back bush (5.3.4 (a) (i))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Front Service brake binding but not excessively (1.2.1 (f))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Rear Suspension arm pin or bush worn but not resulting in excessive movement back bush (5.3.4 (a) (i))

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Nearside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (rear) (5.3.6 (a) (i))

Front Brake pad(s) less than 1.5 mm thick (1.1.13 (a) (ii)) DANGEROUS

Nearside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

Offside Front Tyre worn close to legal limit/worn on edge (5.2.3 (e))

front brakes out of balance o/s/d own

rear shockers bushes perishing

slight movement in bottom arm rear bushes

Nearside Front Anti-roll bar ball joint excessively worn (5.3.4 (a) (i))

Nearside Front Shock absorbers has a serious fluid leak (5.3.2 (b))

Nearside Rear Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

Offside Rear Registration plate lamp inoperative in the case of a single lamp or all lamps (4.7.1 (b) (ii))

front brakes out of balance o/s/d own

rear shockers bushes perishing

slight movement in bottom arm rear bushes

Nearside Front Anti-roll bar linkage has slight play in a ball joint (2.4.G.2)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

n/s/f shocker damp

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

n/s/f shocker damp

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

Front Windscreen wiper not operating automatically when switched on (8.2.1b)

Nearside Rear Tyre worn close to the legal limit (4.1.E.1)

Offside Rear Tyre worn close to the legal limit (4.1.E.1)

back box outer skin corroded

both rear tyres wearing low outer edges

Nearside Front Suspension arm rubber bush deteriorated resulting in excessive movement (2.4.G.2)

Offside Front Suspension arm rubber bush deteriorated resulting in excessive movement (2.4.G.2)

back box corroded

both front shockers have slight misting of oil

front tyres wearing inner edges

Both front shockers damp

Nearside Front Headlamp aim too low (1.8)

Both front shockers damp

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)