2007 Fiat Panda

Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii))

front exhaust shield slightly loos

Windscreen washer not working (3.5 (a))

front exhaust shield slightly loos

Offside Front Track rod end ball joint has slight play (2.1.3 (b) (i))

Offside Front Tyre worn close to legal limit/worn on edge inner edge (5.2.3 (e))

Offside Rear Tyre worn close to legal limit/worn on edge inner edge (5.2.3 (e))

Offside Front Track rod end ball joint has slight play (2.1.3 (b) (i))

Offside Front Tyre worn close to legal limit/worn on edge inner edge (5.2.3 (e))

Offside Rear Tyre worn close to legal limit/worn on edge inner edge (5.2.3 (e))

Offside Side repeater not working (4.4.1 (a) (ii))

Offside Rear Tyre worn close to legal limit/worn on edge at 2.5mm (5.2.3 (e))

Headlamp aim too low both sides (4.1.2 (a))

Offside Side repeater not working (4.4.1 (a) (ii))

Offside Windscreen wiper does not clear the windscreen effectively (3.4 (b) (ii))

Offside Rear Tyre worn close to legal limit/worn on edge at 2.5mm (5.2.3 (e))

Offside Front Anti-roll bar ball joint has slight play (5.3.4 (a) (i))

Nearside Headlamp aim too low (4.1.2 (a))

Nearside Rear Seat belt damaged (7.1.2 (b) (i))

Offside Headlamp aim too low (4.1.2 (a))

Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength axle (5.3.6 (a) (i))

Offside Front Anti-roll bar ball joint has slight play (5.3.4 (a) (i))

Nearside Front Headlamp aim too low (4.1.2 (a))

Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii))

Offside Front Lower Anti-roll bar ball joint excessively worn (5.3.4 (a) (i))

Offside Front Side repeater incorrect colour (4.4.3 (a))

Nearside Front Tyre worn close to legal limit/worn on edge 155/80/13 (5.2.3 (e))

Offside Front Tyre worn close to legal limit/worn on edge 155/80/13 (5.2.3 (e))

Offside Rear Tyre slightly damaged/cracking or perishing 155/80/13 (5.2.3 (d) (ii))

Offside Rear Tyre worn close to legal limit/worn on edge 155/80/13 (5.2.3 (e))

Rear Exhaust mounting defective clamp missing (6.1.2 (a))

Nearside Rear Direction indicator incorrect colour (4.4.3 (a))

Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii))

Windscreen washer not working (3.5 (a))

Nearside Front Tyre tread depth below requirements of 1.6mm (5.2.3 (e)) DANGEROUS

Offside Front Tyre tread depth below requirements of 1.6mm (5.2.3 (e)) DANGEROUS

Nearside Rear Direction indicator slightly discoloured (1.4.A.2f)

Stop lamp has light sources not illuminating, but not more than 50% high level (1.2.1b)

Nearside Front position lamp(s) not working (1.1.A.3b)

Nearside Rear Direction indicator slightly discoloured (1.4.A.2f)

Stop lamp has light sources not illuminating, but not more than 50% high level (1.2.1b)

Offside Front Seat belt damaged but webbing not significantly weakened (5.2.2a)

Nearside Rear Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Rear Body has a sharp edge caused by damage (6.1.C.1)

Offside Rear reflector excessively damaged so that its function is impaired (1.5.1c)

Offside Front Seat belt damaged but webbing not significantly weakened (5.2.2a)

Front Brake pad(s) wearing thin (3.5.1g)

Nearside Front Seat belt stitching slightly frayed (5.2.2b)

exhaust back box outer skin corroded

Nearside Front Suspension arm rubber bush bonding deteriorated resulting in excessive movement (2.4.G.2)

Nearside Rear Direction indicator incorrect colour (1.4.A.2f)

Nearside Track rod end ball joint has excessive play (2.2.B.1f)

Offside Front Anti-roll bar linkage has excessive play in a ball joint (2.4.G.2)

Offside Front Suspension arm rubber bush bonding deteriorated resulting in excessive movement (2.4.G.2)

Nearside Front Seat belt stitching slightly frayed (5.2.2b)

exhaust back box outer skin corroded

Nearside Front Track rod end ball joint has slight play (2.2.B.1f)

Offside Front Anti-roll bar has slight play in a ball joint (2.4.G.2)

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)