2008 Citroen C1

Nearside Front tyre slightly worn on inner edge

Offside Front Tyre worn close to legal limit/worn on edge tyre worn on inner edge (5.2.3 (e))

Offside Front wheel bearing slightly play

Nearside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Nearside Vehicle structure is corroded but structural rigidity is not significantly reduced inner sill (6.1.1 (c) (i))

Offside Front Wheel bearing slightly noisy (5.1.3 (b) (i))

Offside Rear Coil spring corroded (5.3.1 (b) (i))

Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive (5.3.6 (a) (i))

Offside Vehicle structure is corroded but structural rigidity is not significantly reduced inner sill (6.1.1 (c) (i))

Offside Front Suspension arm ball joint dust cover severely deteriorated (5.3.4 (b) (i))

Offside Front Suspension arm pin or bush worn but not resulting in excessive movement rear bush (5.3.4 (a) (i))

Offside Rear Axle swivel pins and bushes swivel pin and/or bush slightly worn (5.1.2 (b) (i))

Offside Registration plate lamp inoperative in the case of multiple lamps or light sources (4.7.1 (b) (i))

Nearside Front Tyre worn close to legal limit/worn on edge worn on inner and outer edge (5.2.3 (e))

Offside Front Tyre worn close to legal limit/worn on edge worn on inner and outer edge (5.2.3 (e))

Front Anti-roll bar linkage pin or bush worn but not resulting in excessive movement both front (5.3.4 (a) (i))

Front Headlamp has a product on the lens but not seriously reducing light output (4.1.4 (b))

Nearside Front Suspension arm pin or bush worn but not resulting in excessive movement rear bush (5.3.4 (a) (i))

Offside Front Suspension arm pin or bush worn but not resulting in excessive movement rear bush (5.3.4 (a) (i))

Rear Axle swivel pins and bushes swivel pin and/or bush slightly worn both rear axle bushes worn (5.1.2 (b) (i))

Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c))

Front Anti-roll bar linkage pin or bush worn but not resulting in excessive movement both front (5.3.4 (a) (i))

Front Headlamp has a product on the lens but not seriously reducing light output (4.1.4 (b))

Nearside Front Suspension arm pin or bush worn but not resulting in excessive movement rear bush (5.3.4 (a) (i))

Offside Front Suspension arm pin or bush worn but not resulting in excessive movement rear bush (5.3.4 (a) (i))

Rear Axle swivel pins and bushes swivel pin and/or bush slightly worn both rear axle bushes worn (5.1.2 (b) (i))

Rear Exhaust has a minor leak of exhaust gases (6.1.2 (a))

Offside Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))

Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii))

Offside Front Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))

Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))

Nearside Stop lamp(s) not working (4.3.1 (a) (ii))

Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i))

Offside Front Lower Suspension arm pin or bush worn but not resulting in excessive movement (5.3.4 (a) (i))

Electronic power steering warning lamp indicates a failure in the system (2.3.8)

Offside Front position lamp(s) not working (1.1.A.3b)

Brake pipe slightly corroded offside front-rear brake pipe (3.6.B.2c)

Front Brake pad(s) less than 1.5 mm thick (3.5.1g)

Nearside Registration plate lamp not working (1.1.C.1d)

Offside Registration plate lamp not working (1.1.C.1d)

Offside Stop lamp not working (1.2.1b)

Nearside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)

Offside Front Tyre tread depth below requirements of 1.6mm (4.1.E.1)