MOT Status
ExpiredMileage
80,647 miBelow or average mileage for this year
Not all car check providers offer a guarantee. Don't risk buying from services that can't back their data. CarVerify reports include a £30,000 finance data guarantee.
Vehicle Details
All premium checks include
50+ data pointsMOT History
Front Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a))
Horn not working (7.7 (a))
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))
Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i))
Nearside Rear Service brake grabbing severely (1.2.1 (c))
Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii))
Offside Front Headlamp not working on main beam (4.1.1 (a) (ii))
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))
Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i))
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))
Service brake efficiency below requirements (1.2.2 (a) (i))
Brake pipe corroded, covered in grease or other material ALL BRAKE LINES COVERED IN UNDERSEAL AND GREASE (1.1.11 (c))
Central Exhaust has a minor leak of exhaust gases (6.1.2 (a))
Front O/S/F INNER FRONT ARCH CORRODED NOT NEAR PESCRIBED AREA
Nearside Front Wheel bearing has slight play (5.1.3 (a) (i))
Offside Front Wheel bearing has slight play (5.1.3 (a) (i))
Horn not working (7.7 (a))
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))
Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i))
Offside Headlamp not working on dipped beam (4.1.1 (a) (ii))
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i))
Offside Side repeater not working (4.4.1 (a) (ii))
Registration plate does not conform to the specified requirements Both (0.1 (d))
All direction indicators flashing less than 60 times a minute (4.4.4 (a))
Offside Seat belt buckle slightly damaged (7.1.2 (d))
extensive corrosion everywhere[not within prescribe areas]
wheel arches corroded
Nearside Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii))
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis at rearmost spring hanger mount (5.3.6 (a) (i))
Nearside Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii))
Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c))
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis at rearmost spring hanger mount (5.3.6 (a) (i))
Exhaust has a minor leak of exhaust gases (6.1.2 (a))
Front Suspension component mounting prescribed area is corroded but not considered excessive both jacking points (5.3.6 (a) (i))
Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt both outer (6.1.7 (g) (ii))
Front Headlamp not working on dipped beam (4.1.1 (a) (ii))
Front Headlamp not working on main beam (4.1.1 (a) (ii))
Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting wheel arch (6.2.2 (d) (i))
Parking brake efficiency below requirements (1.4.2 (a) (i))
Service brake efficiency below requirements (1.2.2 (a) (i))
Exhaust has a minor leak of exhaust gases (6.1.2 (a))
Front Brake hose slightly damaged cracked (1.1.12 (b) (i))
Horn not loud enough to be heard by another road user (7.7 (c) (i))
Engine mounting bracket damaged or deteriorated resulting in excessive movement bolt missing (6.1.8 (a) (i))
Front Headlamp aim too far to the left (4.1.2 (a))
Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting center (6.2.2 (d) (i))
Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill outer (6.1.1 (c) (i))
Parking brake efficiency below requirements (1.4.2 (a) (i))
Service brake efficiency below requirements (1.2.2 (a) (i))
Exhaust has a minor leak of exhaust gases (6.1.2 (a))
Front Brake hose slightly damaged cracked (1.1.12 (b) (i))
Horn not loud enough to be heard by another road user (7.7 (c) (i))
Offside Front Brake hose slightly deteriorated x2 cracking (3.6.B.4d)
Offside Front Suspension component mounting prescribed area is corroded but not considered excessive under wheel arch inner wing (2.4.A.3)
Offside Rear Suspension component mounting prescribed area is corroded but not considered excessive underwheel arch (2.4.A.3)
Parking brake lever has little reserve travel (3.1.6b)
Front Inner Brake pad(s) wearing thin (3.5.1g)
Front brake discs in poor condition
Exhaust system not adequately supported all rubbers split perished and some missing (7.1.1)
Nearside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2)
Nearside Front Outer Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a)
Nearside Rear Suspension component mounting prescribed area is excessively corroded rear spring rear mounting outer sill area marked yellow (2.4.A.3)
Nearside Rear Suspension component mounting prescribed area is excessively corroded spring rear mounting inner sill area marked yellow (2.4.A.3)
Nearside Windscreen wiper does not clear the windscreen effectively (8.2.2)
Nearside rear brake recording little or no effort (3.7.B.5a)
Nearside rear parking brake recording little or no effort (3.7.B.6a)
Offside Headlamp aim too high (1.8)
Offside Rear Suspension component mounting prescribed area is excessively corroded rear spring rear mounting outer sill area marked yellow (2.4.A.3)
Offside Windscreen wiper does not clear the windscreen effectively (8.2.2)
Offside rear parking brake recording little or no effort (3.7.B.6a)
Parking brake: efficiency below requirements (3.7.B.7)
rear brake application uneven (3.7.B.2)
Front Inner Brake pad(s) wearing thin (3.5.1g)
Front brake discs in poor condition
Direction indicators flashing more than 120 times a minute (1.4.A.2g)
Hazard warning lamps not flashing in phase, with ignition off (1.4.B.1f)
Offside Front Headlamp aim too high (1.8)
Parking brake: efficiency below requirements (3.7.B.7)
Rear Registration plate lamp not working (1.1.C.1d)
Exhaust has a minor leak of exhaust gases (7.1.2)
exhaust system rubbers split perished and missing
n/s/r tyre cracked and perishing
Nearside Rear Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)
Nearside Rear Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)
Offside Headlamp not working on dipped beam (1.7.5a)
Offside Headlamp not working on main beam (1.7.5a)
Offside Rear Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)
Offside Rear Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)
Offside Rear Tyre has a bulge, caused by separation or partial failure of its structure (4.1.D.1b)
Parking brake lever has no reserve travel (3.1.6b)
Exhaust has a minor leak of exhaust gases (7.1.2)
exhaust system rubbers split perished and missing
n/s/r tyre cracked and perishing
Battery insecure (1.9.1)
Brake load sensing valve seized (3.6.E.3)
Horn not working (1.6.2a)
Nearside Front Lower Suspension arm has excessive play in a ball joint (2.4.G.2)
Nearside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3)
Nearside Headlamp not working on dipped beam (1.7.5a)
Nearside Rear Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)
Nearside Rear Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)
Nearside Rear Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)
Nearside Seat belt anchorage prescribed area is inadequately repaired (5.2.6)
Offside Front Brake pipe fouled by moving parts (3.6.B.2a)
Offside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3)
Offside Rear Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)
Offside Rear Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)
Offside Rear Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)
Offside Seat belt anchorage prescribed area is inadequately repaired (5.2.6)
Nearside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
Offside Front Suspension component mounting prescribed area is corroded but not considered excessive (2.4.A.3)
battery tray corroded and holed
reverse light not working
Nearside Front Windscreen wiper does not clear the windscreen effectively (8.2.2)
Nearside Inner Front Seat belt anchorage prescribed area is excessively corroded (5.2.6)
Nearside Outer Front Seat belt anchorage prescribed area is excessively corroded (5.2.6)
Nearside Rear Suspension spring mounting prescribed area is excessively corroded (2.4.A.3)
Nearside rear brake binding (3.7.B.1)
Offside Front Windscreen wiper does not clear the windscreen effectively (8.2.2)
Offside Inner Front Seat belt anchorage prescribed area is excessively corroded (5.2.6)
Offside Outer Front Seat belt anchorage prescribed area is excessively corroded (5.2.6)
Offside Rear Brake pipe inadequately clipped (3.6.B.1)
Offside rear brake binding (3.7.B.1)
nearside front outrigger is excessively corroded but not within prescribed area
offside front outrigger is excessively corroded but not within prescribed area
reverse light not working
Brake load sensing valve linkage stiff (3.6.E.3)
nearside front outer sill badly corroded
nearside front wheel arch corroded
nearside rear wheel arch corroded
offside front outer sill badly corroded
offside front windsreen surround corroded and holed
Nearside rear brake binding (3.7.B.1)
Nearside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3)
Nearside Stop lamp not working (1.2.1b)
Offside Front Body has a sharp edge caused by corrosion (6.1.C.1)
Offside Rear Body has a sharp edge caused by corrosion (6.1.C.1)
Offside Windscreen washer provides insufficient washer liquid (8.2.3)
Offside rear brake binding (3.7.B.1)
Registration plate lamp not working (1.1.C.1d)
Brake load sensing valve linkage stiff (3.6.E.3)
nearside front outer sill badly corroded
nearside front wheel arch corroded
nearside rear wheel arch corroded
offside front outer sill badly corroded
offside front windsreen surround corroded and holed
Nearside Front Headlamp not working on dipped beam (1.7.5a)
Nearside Front Headlamp not working on main beam (1.7.5a)
Offside Rear fog lamp not working (1.3.2b)
Offside Windscreen wiper does not clear the windscreen effectively (8.2.2)
Nearside Headlamp aim too low (1.8)
Offside Headlamp aim too high (1.8)
Brake load sensing valve linkage seized (3.6.E.3)
Exhaust system not adequately supported (7.1.1)
Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)
Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)
Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)
Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)
Nearside Rear wheel bearing has excessive play (2.6.2)
Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2)
How Reliable is the Talbot Motorhome?
Based on 3,205 MOT tests across 170 vehicles.
Top MOT Failure Points
Don't risk it. Know before you buy.
Not all vehicle check providers are the same. Some don't offer a data guarantee, which means if their information is wrong, you're on your own. Every CarVerify report is backed by a £30,000 finance data guarantee.
J363 CCH is a 1991 Talbot Motorhome in White with a 1,971cc petrol engine. This vehicle has been through 33 MOT tests with a personal pass rate of 54.5%.
Across all 1991 Talbot Motorhome models, the average MOT pass rate is 65.8% with a typical mileage of 82,313 miles. This particular vehicle has a lower pass rate than the average for its year, which may indicate maintenance issues worth investigating.
The most common reason a Talbot Motorhome fails its MOT is suspension component mounting prescribed area is excessively corroded, accounting for 182 recorded failures. If you're considering buying J363 CCH, it's worth having these areas checked by a mechanic before committing.
The Talbot Motorhome typically stays on UK roads for around 42 years. At 35 years old, this Talbot Motorhome is approaching the upper end of the typical lifespan for this model.
Frequently Asked Questions
How do I check the history of J363 CCH?
You can check the full history of J363 CCH by running a full vehicle check. This shows you finance, stolen, write-off, MOT history, mileage records and more.
What year was J363 CCH registered?
J363 CCH is a 1991 Talbot Motorhome, first registered on 9 August 1991.
Is J363 CCH safe to buy?
The MOT history for J363 CCH shows 33 tests with a 54.5% pass rate. To check for outstanding finance, stolen markers, write-off history and mileage discrepancies, run a full vehicle check.
Does J363 CCH have outstanding finance?
Finance checks require a premium vehicle report. This checks against all major UK finance providers to see if there is any outstanding finance on J363 CCH. If you buy a car with outstanding finance, the finance company can repossess it.
No warranty or guarantee of accuracy is provided for any free data on this page. The data guarantee applies only to information obtained through the purchase of a full check.